Grizzly G0561 owner manual Feed Rate, To set the feed rate

Page 28

Feed Rate

The speed at which the saw blade will cut through a workpiece is controlled by blade type, feed rate, and feed pressure.

Note: If a lubricant is used on the cut, the feed rate can be increased by approximately 15%.

To set the feed rate:

1.Raise the bow to the maximum height to remove spring tension. Close the ON/OFF valve to lock the bow in place.

2.Using a 9⁄16" wrench, adjust the feed pressure tension spring. Tighten enough to remove play but not enough to apply tension to the spring (see Figure 30).

Note: This spring adjustment is an initial set- ting. Depending on cutting circumstances, you will have to fine-tune the feed pressure with this adjustment. Increasing the spring tension will reduce the feed pressure.

Spring

Adjustment Nut

Figure 30. Spring tension adjustment.

3.Clamp the workpiece in the table vise.

4.Close the feed ON/OFF valve shown in Figure 31, to lock the bow and blade a few inches above the workpiece.

Feed Rate Dial

ON/OFF Valve

Figure 31. Feed rate dial.

5.With the correct saw blade and blade speed selected, turn the saw and lubricant pump ON.

6.Open the ON/OFF valve, then slowly rotate the feed rate dial clockwise to a slow feed rate until the saw begins to cut the workpiece (see Figure 31).

7.Observe the chips that exit the cut, and increase or decrease the feed rate according to the chip characteristics.

—If you get a tightly curled, warm shavings, brown to black in color, you are using too much downward pressure.

—Blue looking chips are caused by extreme heat from too high blade speed.

—Thin powder-like chips are from insufficient feed pressure. This will dull your blade rap- idly.

—The best cut and feed rate will give you evenly shaped spiraled curls with very little color change, if any at all.

-26-

G0561 7" x 12" Metal-Cutting Bandsaw

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Model G0561 METAL-CUTTING Bandsaw Page Table of Contents Service Accessories MaintenanceWarranty and Returns Foreword IntroductionContact Info Machine Data Sheet Table Info Identification Safety Safety Instructions for MachineryAlways Lock Mobile Bases if Used Before Operating Machinery Safety Instructions for Metal Cutting Bandsaws Circuit Requirements Wiring for110/220V Operation Grounding Extension Cords Setup Setup SafetyItems Needed for Setup UnpackingInventory Box Contents Figure QtyHardware Bag Hardware Recognition Chart Cleanup Site ConsiderationsTo install the work stop Shipping BracketWork Stop To remove the shipping bracketTo install the wheels and leveling feet To install the chip screenWheels & Leveling Feet Chip ScreenTo install the pulley cover Pulley CoverTo install the handle BeltHandle To tension or change the V-belt positionVertical Assembly To assemble the bandsaw for vertical cut- tingRecommended Adjustments AdjustmentsFactory adjustments that should be verified Test RunOperations Operation Safety ViseTo square the blade to the vise Blade Speed To adjust the angle on the viseTo change blade speeds Blade Selection Blade GuidesCutting Fluid System E C T R O C U T I O NCutting Fluid Biological Poison HazardFeed Rate To set the feed rateTips for horizontal cutting Operation TipsTips for vertical cutting H5405-LenoxLube Tube AccessoriesG7897-Machining Fluid H1302 H4979 H4977 H1302-Standard EarmuffsH1300 H1298 G7984 H2347 H0736 Maintenance CleaningSchedule LubricationService TroubleshootingBandsaw Operations Blade Change To change the blade on the bandsawTo adjust the blade tracking on the bandsaw Blade Tension TrackingSquaring the Blade To square the blade to the bed of the tableTo adjust the blade guide bearings Blade Guide BearingsElectrical Components Circuit breaker and capacitorG0561 110V & 220V Wiring Diagram G0561 Cabinet/Base G0561 Bow/Motor G0561 Gear Box Parts List DescriptionGear BOX Assembly Motor Mount Plate Machine Labels & Parts List Safety Label PlacementWarranty and Returns Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAPage Call Today For a Free Full Color Catalog

G0561 specifications

The Grizzly G0561 is a high-performance wood lathe that has become a favorite among both amateur and professional woodworkers. This machine is designed with precision and versatility in mind, making it an ideal choice for those looking to enhance their woodworking projects.

One of the standout features of the Grizzly G0561 is its robust cast iron construction, which provides not only durability but also stability during operation. This solid construction minimizes vibrations, allowing for smoother cuts and a better finish on various workpieces. The lathe is equipped with a powerful 1-horsepower motor that delivers ample torque, making it suitable for turning larger and more complex projects.

The G0561 also features a variable speed control, giving users the ability to adjust the spindle speed from 600 to 2400 RPM. This range allows for greater flexibility when working with different types of wood and varying project requirements. The digital readout for speed monitoring makes it easier for users to achieve the desired results with consistency.

Another impressive characteristic of this lathe is its 14-inch swing over bed, providing ample space for working on larger items while maintaining precision. The bed length is 42 inches, accommodating a variety of spindle lengths. The tailstock can be easily adjusted and locked in place, enabling users to effectively work on projects such as bowls or spindles.

The Grizzly G0561 also comes equipped with a quick-change tool rest system that allows for easy adjustments and transitions between different turning techniques. With a variety of tool rest heights, woodworkers can easily switch to the most suitable configuration for their specific task. Additionally, the built-in indexing head allows for precise marking and cutting, making it easier to create detailed patterns.

Incorporating advanced engineering and user-friendly features, the G0561 places a premium on safety with a thoughtfully designed on/off switch and an emergency stop button. This enhances the overall user experience while ensuring that safety remains a top priority in woodworking.

In summary, the Grizzly G0561 wood lathe combines durability, power, and versatility, making it an exceptional choice for woodworkers looking to elevate their craft. Its robust design, variable speed capabilities, and user-friendly features contribute to its reputation as a reliable and efficient tool in any woodworking shop. Whether for professional use or hobbyist projects, the G0561 stands out as a remarkable piece of equipment that meets the demands of today’s woodturning enthusiasts.
Top Page Image Contents