Grizzly G0621 owner manual Table of Contents

Page 3

Table of Contents

INTRODUCTION	2
Foreword	2
Contact Info	2
Machine Data Sheet	3
Identification	5
SECTION 1: SAFETY	6
Safety Instructions for Machinery	6
Additional Safety Instructions for Bandsaws . 8
SECTION 2: CIRCUIT REQUIREMENTS	9
220V Single-Phase	9
SECTION 3: SETUP	10
Setup Safety	10
Items Needed for Setup	10
Unpacking	10
Inventory	11
Hardware Recognition Chart	12
Clean Up	13
Site Considerations	13
Assembly	14
Dust Collection	17
Blade Tracking	17
Test Run	18
Tensioning Blade	19
Adjusting Support Bearings	19
Adjusting Blade Guides	21
Adjusting Positive Stop	22
Setting Table	22
Tilt Scale to 0˚	22
Aligning Table	23
Aligning Fence	23
SECTION 4: OPERATIONS	24
Operation Safety	24
Basic Controls	24
Workpiece Inspection (Wood)	25
Overview	25
Table Tilt	26
Guide Post	26
Ripping	27
Crosscutting	27
Resawing	28
Cutting Curves	29
Stacked Cuts	29
Blade Selection (Wood Cutting)	30
Blade Selection (Metal Cutting)	32
Blade Changes	33
Scale Calibration	34

SECTION 5: ACCESSORIES	35
SECTION 6: MAINTENANCE	36
Schedule	36
Cleaning	36
Lubricating	36
Redressing Rubber Tires	36
SECTION 7: SERVICE	37
Troubleshooting	37
Servicing V-Belts	39
Shimming Table	41
Blade Lead	41
Wheel Alignment	42
Electrical Components	44
Wiring Diagram	45
Main Parts Breakdown	46
Main Parts List	47
Table/Blade Guides Parts Breakdown	48
Secondary Parts Breakdown	49
Stand Parts Breakdown	50
Fence Parts Breakdown	51
Safety Labels Parts Breakdown	52
WARRANTY AND RETURNS	53

Image 3

Contents Model G0621 WOOD/METAL Bandsaw Page Table of Contents Introduction ForewordContact Info Machine Data Sheet G0621 Wood/Metal Bandsaw Identification Safety G0621 Wood/Metal Bandsaw Additional Safety Instructions for Bandsaws Circuit Requirements 220V Single-PhaseUnpacking SetupSetup Safety Items Needed for SetupInventory Main Components Figure QtyFasteners and Tools not shown Qty Hardware Recognition Chart Floor Load Clean UpPlacement Location Site ConsiderationsTo assemble the bandsaw AssemblyPage Dust port installation G0621 Wood/Metal Bandsaw Dust Collection Blade Tracking To connect a vacuum hoseTo center track the blade Changes in the blade tension may change the blade tracking Test RunTo tension the bandsaw blade Adjusting Support BearingsTo adjust the support bearings Tensioning BladeG0621 Wood/Metal Bandsaw To adjust the upper and lower blade guides Adjusting Blade GuidesTo calibrate the pointer on the table tilt scale Adjusting Positive StopSetting Table Tilt Scale to 0˚ To set the positive stop 90˚ to the bladeTo align the fence parallel with the miter slot Aligning TableAligning Fence To align the miter slot parallel to the bandsaw bladeOperations Operation Safety Basic ControlsIrregular Cuts Workpiece Inspection WoodOverview Straight CutsPositive stop must be removed to move the table to the left Table TiltGuide Post To tilt the tableRippingCrosscutting To make a rip cutTo make a 90˚ crosscut Typical resawing operation ResawingTo complete a stacked cut Cutting Curves Stacked CutsTooth Style Blade Selection Wood CuttingBlade Length Blade WidthMost common causes of blade breakage are Tooth PitchBlade Care Blade BreakageTo select the correct blade TPI Blade Selection Metal CuttingTo replace the blade Blade ChangesTo calibrate the scale Scale CalibrationG1928-Bandsaw Handbook AccessoriesGrizzly Bandsaw Blades G7315-Super Heavy-Duty Mobile BaseLubricating MaintenanceCleaning ScheduleService TroubleshootingMotor & Electrical Miscellaneous Cutting OperationsAccessing V-Belts Servicing V-BeltsChecking V-Belts Tensioning/Replacing V-Belts Shimming Table Blade Lead To shim the tableTo skew your fence Verifying Upper/Lower Wheels are Coplanar Wheel AlignmentAdjusting Lower Wheel To adjust the lower wheelShimming Upper Wheel Motor junction box wiring Electrical Component WiringWiring Diagram Breakdown Description Main Parts ListTable/Blade Guides Parts Breakdown Secondary Parts Breakdown Stand Parts Breakdown Fence Parts Breakdown Safety Labels Parts Breakdown Warranty and Returns Page Page Page