Grizzly ZX3 instruction manual Service Adjustments, 45˚ & 90˚ Stops

Page 44

SECTION 8: SERVICE ADJUSTMENTS

!

Disconnect power to the

machine when perform-

ing

any

maintenance,

 

assembly

or

adjust-

 

ments. Failure to do this

 

may

result in

serious

 

personal injury.

 

Keep loose clothing rolled up and out of the way of machinery and keep hair pulled back.

Wear safety glasses during the entire adjust- ment process. Failure to comply may result in serious personal injury.

45˚ & 90˚ Stops

1.Set your blade angle at zero as shown on the angle indicator on the front of the saw and raise the blade several inches above the table.

2.Place a machinistÕs square flat on the table and slide it alongside the blade. The square should contact the blade evenly from bottom to top. Make sure that a blade tooth does not obstruct the movement of the square.

3.Adjust the handwheel until the square is flush with the blade. Loosen the tilt indicator arrow, set to zero, and retighten. Loosen and adjust the stop bolt on the left side of the front trunnion to allow a 90¡ stop point. See Figure 40 for details.

4.Turn the blade angle handwheel until the angle indicator points at the desired angle.

5.Tighten the handwheel locking knob.

6.Repeat Steps 1-6for setting the blade to 45¡ and adjust the 45¡ stop bolt on the right side of the front trunnion. Use the 45¡ side of a combo square or a bevel gauge set at 45¡.

45û Stop Bolt

90û Stop Bolt

Figure 40. Geared trunnion.

-42-

G1023Z Series Heavy-Duty 10'' Table Saw

Page 43 Page 45
Image 44
Page 43 Page 45
Contents HEAVY-DUTY Table SAW Model G1023Z, ZX & ZX3Page Table of Contents Safety Safety Instructions For Power ToolsLength AMP Rating 25ft 50ft 100ftAdditional Safety Instructions For Table Saws Avoiding Kickback Safety Accessories Following can help minimize kickbacksFeatherboards Zero Clearance Table InsertsPush Paddles Introduction CommentaryCircuit Requirements G1023ZG1023ZX G1023ZX3 Grounding Extension Cord Machine Features Terms & DefinitionsMain Features SET UP Unpacking Piece InventoryG1023Z Series component layout Hardware Recognition Chart Clean Up Site ConsiderationsFloor Load Working ClearanceBeginning Assembly Extension Wings Switch To mount the switchDisconnect the machine from the power source Fence & RailsTo mount the dust hood and cleanout door Dust Hood Motor CoverMotor Brace Guard BracketHandwheel Table InsertSaw Blade Blade Guard/SplitterFront Support Blade Adjustment Bolt To adjust the miter gauge Miter GaugeStarting the machine Recommended adjustment checklistStart Up Recommended Operations Blade SelectionPage Crosscutting Cross-cut operation G1023Z Series Heavy-Duty 10 Table SawRipping Ripping operationDado Cutting Single-blade dado cutIf the cut is satisfactory, repeat with your fin- ish stock Rabbet Cutting Sacrificial fence G1023Z Series Heavy-Duty 10 Table SawCutting rabbets with the dado blade Rabbet cutting G1023Z Series Heavy-Duty 10 Table SawCutting rabbets with the standard blade Rabbet cutting G1023Z Series Heavy-Duty 10 Table Saw Maintenance GeneralLubricate the areas indicated below every 12 months LubricationTableBelt Belt deflection Date Approximate Hours Of Use Maintenance Performed Service Adjustments 45˚ & 90˚ StopsBlade Parallelism Page Blade Alignment Trunnion mounting boltsPage G1023Z Series Heavy-Duty 10 Table Saw G1023Z Series Heavy-Duty 10 Table Saw Page Closure Machine Data Sheet G1023Z / G1023ZX / G1023ZX3G1023Z Series Heavy-Duty 10 Table Saw Cabinet Complete Miter Gauge Troubleshooting Guide Symptom Possible Cause Corrective ActionG1023Z Series Heavy-Duty 10 Table Saw G1023Z Series Heavy-Duty 10 Table Saw Warranty and Returns Warranty Card Grizzly INDUSTRIAL, INC BOX BELLINGHAM, WACall Today For a Free Full Color Catalog

ZX, ZX3 specifications

The Grizzly ZX3 and ZX are part of an innovative lineup of all-terrain vehicles designed for enthusiasts who demand rugged performance and reliability. These models are engineered with cutting-edge technologies and superior design to tackle challenging terrains while ensuring rider comfort and convenience.

One of the standout features of the Grizzly ZX3 and ZX is their powerful engine options. Equipped with a high-performance, fuel-efficient engine, these vehicles provide impressive torque and acceleration, making them ideal for off-road adventures. The enhanced engine is complemented by an advanced transmission system, ensuring smooth gear shifts and optimal power distribution across varying landscapes.

Durability is a hallmark of the Grizzly ZX3 and ZX. Constructed with a robust chassis and high-strength materials, these vehicles are designed to withstand the rigors of off-road use. The rugged suspension system, featuring adjustable shocks, allows for superior handling and stability, whether navigating rocky trails or muddy paths. This level of suspension performance translates into a smoother ride, reducing driver fatigue on longer excursions.

In terms of technology, the Grizzly ZX3 and ZX boast a sophisticated instrument cluster that provides real-time data on speed, fuel consumption, and battery status. Enhanced connectivity features, such as Bluetooth integration, enable riders to connect their devices for seamless navigation and communication. Additionally, the inclusion of GPS systems ensures that users can explore new territories with confidence, knowing they are always on the right track.

Safety is a priority in the design of the Grizzly ZX3 and ZX. These models come equipped with advanced braking systems that enhance stopping power, along with features such as roll-over protection and secure seating to protect occupants during rough rides. Visibility is enhanced through high-intensity LED lighting, ensuring that riders are well aware of their surroundings, day or night.

Ergonomically designed seating and ample storage solutions make these models user-friendly. Whether it’s a day of exploring or transporting gear, the Grizzly ZX3 and ZX seamlessly blend comfort with functionality.

In summary, the Grizzly ZX3 and ZX are engineered for adventure. Their powerful performance, durability, advanced technologies, and safety features create an all-terrain experience that is second to none, ensuring that every ride is exhilarating and memorable. Whether you're an off-road veteran or a newcomer, these vehicles will elevate your outdoor adventures.
Top Page Image Contents