Grizzly ZX3 instruction manual Blade Alignment, Trunnion mounting bolts

Page 47

Blade Alignment

The blade position can be adjusted slightly in case it contacts the table insert when raised or tilted. This adjustment can be made either by moving the whole trunnion assembly, or by just moving the arbor bracket. Try adjusting by mov- ing the whole trunnion first, this is the easier of the two ways.

To adjust the blade position by moving the trunnion:

1.Disconnect the machine from the power source!

2.Remove the table and wings and set them to one side. Be sure to note the position of the table shims. Replace them to their original position before re-attaching the table.

3.Loosen the four trunnion mounting bolts as shown in Figure 45, and nudge to either the left or right depending on where the blade is hitting the saw.

Trunnion Mount Bolts

Figure 45. Trunnion mounting bolts.

The table and wings rep- resent a very heavy load. DO NOT over- exert yourself while lift- ing or moving the table and wings – get assis- tance.

G1023Z Series Heavy-Duty 10'' Table Saw

4.Reattach the table, making sure there is ade- quate blade clearance through all blade adjustments. Recheck guard alignment to the blade and to the table top. Adjust as nec- essary and tighten down all the bolts before use.

5.If the blade is still contacting the insert, repeat Steps 1-4. Check all other adjust- ments.

6.Recheck the blade to miter slot adjustments, and adjust as necessary.

Bracket Lock Bolt

Arbor Bracket

Figure 46. Adjusting arbor bracket.

To adjust the blade position by moving the arbor bracket:

1.Disconnect the machine from the power source!

2.Remove the table and wings and set them to one side. Be sure to note the position of the table shims. Replace them to their original position before re-attaching the table.

3.Loosen the bracket lock bolt shown in

Figure 46.

4.Slowly slide the arbor bracket towards the end of the shaft.

NOTICE

If you make the adjustment described in this section, check and adjust the blade splitter to make sure it aligns with the blade.

-45-

Page 46 Page 48
Image 47
Page 46 Page 48
Contents Model G1023Z, ZX & ZX3 HEAVY-DUTY Table SAWPage Table of Contents Safety Instructions For Power Tools Safety25ft 50ft 100ft Length AMP RatingAdditional Safety Instructions For Table Saws Following can help minimize kickbacks Avoiding Kickback Safety AccessoriesFeatherboards Zero Clearance Table InsertsPush Paddles Commentary IntroductionG1023Z Circuit RequirementsG1023ZX G1023ZX3 Grounding Extension Cord Terms & Definitions Machine FeaturesMain Features Unpacking Piece Inventory SET UPG1023Z Series component layout Hardware Recognition Chart Working Clearance Clean UpSite Considerations Floor LoadBeginning Assembly Extension Wings Fence & Rails SwitchTo mount the switch Disconnect the machine from the power sourceDust Hood Motor Cover To mount the dust hood and cleanout doorGuard Bracket Motor BraceTable Insert HandwheelBlade Guard/Splitter Saw BladeFront Support Blade Adjustment Bolt Miter Gauge To adjust the miter gaugeStarting the machine Recommended adjustment checklistStart Up Recommended Blade Selection OperationsPage Cross-cut operation G1023Z Series Heavy-Duty 10 Table Saw CrosscuttingRipping operation RippingSingle-blade dado cut Dado CuttingIf the cut is satisfactory, repeat with your fin- ish stock Sacrificial fence G1023Z Series Heavy-Duty 10 Table Saw Rabbet CuttingRabbet cutting G1023Z Series Heavy-Duty 10 Table Saw Cutting rabbets with the dado bladeCutting rabbets with the standard blade Rabbet cutting G1023Z Series Heavy-Duty 10 Table Saw General MaintenanceLubricate the areas indicated below every 12 months LubricationTableBelt Belt deflection Date Approximate Hours Of Use Maintenance Performed 45˚ & 90˚ Stops Service AdjustmentsBlade Parallelism Page Trunnion mounting bolts Blade AlignmentPage G1023Z Series Heavy-Duty 10 Table Saw G1023Z Series Heavy-Duty 10 Table Saw Page Closure G1023Z / G1023ZX / G1023ZX3 Machine Data SheetG1023Z Series Heavy-Duty 10 Table Saw Cabinet Complete Miter Gauge Symptom Possible Cause Corrective Action Troubleshooting GuideG1023Z Series Heavy-Duty 10 Table Saw G1023Z Series Heavy-Duty 10 Table Saw Warranty and Returns Warranty Card BOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCCall Today For a Free Full Color Catalog

ZX, ZX3 specifications

The Grizzly ZX3 and ZX are part of an innovative lineup of all-terrain vehicles designed for enthusiasts who demand rugged performance and reliability. These models are engineered with cutting-edge technologies and superior design to tackle challenging terrains while ensuring rider comfort and convenience.

One of the standout features of the Grizzly ZX3 and ZX is their powerful engine options. Equipped with a high-performance, fuel-efficient engine, these vehicles provide impressive torque and acceleration, making them ideal for off-road adventures. The enhanced engine is complemented by an advanced transmission system, ensuring smooth gear shifts and optimal power distribution across varying landscapes.

Durability is a hallmark of the Grizzly ZX3 and ZX. Constructed with a robust chassis and high-strength materials, these vehicles are designed to withstand the rigors of off-road use. The rugged suspension system, featuring adjustable shocks, allows for superior handling and stability, whether navigating rocky trails or muddy paths. This level of suspension performance translates into a smoother ride, reducing driver fatigue on longer excursions.

In terms of technology, the Grizzly ZX3 and ZX boast a sophisticated instrument cluster that provides real-time data on speed, fuel consumption, and battery status. Enhanced connectivity features, such as Bluetooth integration, enable riders to connect their devices for seamless navigation and communication. Additionally, the inclusion of GPS systems ensures that users can explore new territories with confidence, knowing they are always on the right track.

Safety is a priority in the design of the Grizzly ZX3 and ZX. These models come equipped with advanced braking systems that enhance stopping power, along with features such as roll-over protection and secure seating to protect occupants during rough rides. Visibility is enhanced through high-intensity LED lighting, ensuring that riders are well aware of their surroundings, day or night.

Ergonomically designed seating and ample storage solutions make these models user-friendly. Whether it’s a day of exploring or transporting gear, the Grizzly ZX3 and ZX seamlessly blend comfort with functionality.

In summary, the Grizzly ZX3 and ZX are engineered for adventure. Their powerful performance, durability, advanced technologies, and safety features create an all-terrain experience that is second to none, ensuring that every ride is exhilarating and memorable. Whether you're an off-road veteran or a newcomer, these vehicles will elevate your outdoor adventures.
Top Page Image Contents