Parkside PPHSS 730 SE manual Included items, Technical information, Workplace safety

Page 8

Introduction / General safety advice for electrical power tools

 

Included items

values given in these instructions. It is easy to underes-

 

 

 

 

timate the vibration load if the electrical power tool is

1

Jigsaw including

used regularly in particular circumstances.

 

- Dust extraction spout

 

 

- Allen key

Note: If you wish to make an accurate assessment

 

- Chip guard

of the vibration loads experienced during a particu-

1

Guide fence

lar period of working, you should also take into

1

Operating instructions

account the intervening periods of time when the

 

 

 

 

device is switched off or is running but is not actual-

 

 

 

 

ly in use. This can result in a much lower vibration

 

 

 

 

 

 

 

 

load over the whole of the period of working.

2Saw blades for wood

1 Saw blade for metal

Technical information

Jigsaw:

Parkside PPHSS 730 SE

Rated voltage:

230 V ~ 50 Hz

Power consumption:

730 W

No-load speed:

max. n0 600 - 2900 min-1

Cutting depth:

max. 110 mm

Pendulum action:

3 speeds and a fine

 

cutting setting

Inclined cut:

0 - 45° left / right

Protection class:

II /

Noise and vibration data:

Values determined in accordance with EN 60745. The sound pressure level (A-weighted) of the device is typically 90 dB (A). Uncertainty K = 3 dB. The sound level while working can exceed 101 dB (A).

Wear ear protection!

Evaluated acceleration, typical: Hand / arm vibration ah = 6,268 m / s2 Uncertainty K = 1,5 m / s2

WARNING! The vibration level given in these instructions has been measured in accordance with a standardised measurement procedure specified in EN 60745 and can be used to compare devices. Different uses of the device give rise to different vibra- tion levels and in many cases they may exceed the

General safety advice for electrical power tools

WARNING! Read all the safety advice and instructions! Failure to observe the safety advice and instructions may result in electric shock, fire and / or serious injury.

KEEP ALL THE SAFETY ADVICE AND INSTRUC- TIONS IN A SAFE PLACE FOR FUTURE REFER- ENCE! THE TERM “ELECTRICAL TOOL” USED IN THE SAFETY ADVICE REFERS TO ELECTRICAL TOOLS POWERED BY MAINS ELECTRICITY (BY MEANS OF A MAINS LEAD) AND ELECTRICAL TOOLS POWERED BY RECHARGEABLE BATTER- IES (WITHOUT A MAINS LEAD).

1. Workplace safety

a)Keep your working area clean and well lit. Untidy or poorly lit working areas can lead to accidents.

b)Do not work with the device

in potentially explosive envi- ronments in which there

are inflammable liquids, gases or dusts. Electrical power tools create sparks, which can ignite dusts or fumes.

c)Keep children and other peo-

ple away while you are op- erating the electrical tool.

Distractions can cause you to lose control of the device.

GB/IE/CY

7

Image 8
Contents Pphss 730 SE Page 13 12 10 9 10 mm 260 mm 70 mm 65 mm 30 mm 205 mm 110 mm 150 mm 10 mm 395 mm x 185 mm x 10 mm 395 mm x 120 mm x 10 mm Table of contents Features and equipment IntroductionJigsaw Pphss 730 SE Introduction Proper useTechnical information Workplace safetyIncluded items General safety advice for electrical power tools Electrical safetyPersonal safety Careful handling and use of electrical power toolsDo not work on moistened materials or damp surfaces Safety advice relating specifically to this deviceAfter switching off do not brake the saw blade Original accessories / attachments Information about saw bladesMounting / replacing saw blades Attaching the chip guardPreparing for use / Operation / Maintenance and cleaning Accordance with European Directive Service centre WarrantyDisposal Declaration of Conformity / Manufacturer Declaration of Conformity ManufacturerKompernass Gmbh