Woodstock W1761, W1762 owner manual Support leg fastened to main Extension table

Page 34

W1761/W1762 12" Table Saw with Riving Knife

SET UP

11.Fasten each support leg to the main extension table with four M6-1 x 12 Phillips head screws and flat washers as shown in Figure 20.

12.Rotate both feet until they touch the ground, and tighten the hex nuts to secure the feet.

13.Fasten the shelf end plate to the legs with four M6-1 x 12 Phillips head screws and flat washers as shown in Figure 21.

14.Place the shelf brackets between the cabinet and shelf end plate, and fasten with four M6-1 x 12 hex bolts, and two flat washers and two hex nuts (on the end plate), as shown in Figure 22.

15.Place the lower shelf on the brackets.

16.Place the 93" fence tube over the 93" front rail and secure with nine M8-1.25 x 12 flange bolts as shown in Figure 23.

-20-

Figure 20. Support leg fastened to main

extension table.

Figure 21. Installing shelf end plate on

extension table legs.

Flange

Shelf Bracket

Figure 22. Shelf brackets installed.

Flange Bolt

Figure 23. Fence tube mounted to front

fence rail.

Image 34

Contents Table SAW with Riving Knife Important Changes to Assembly Inventory DifferencesBlade Requirements Blade InstallationBlade Size Requirements Guard Blade GuardSpreader Installing Blade Guard & Spreader Location to secure blade guard ScrewAnti-Kickback Pawls To remove the pawls, do these stepsWhen to Use the Blade Guard When Not to Use the Blade GuardWhen Not to Use the Riving Knife Installing Riving KnifeWhen to Use the Riving Knife Riving KnifeChecking Alignment Spreader or Riving Knife AlignmentTools Needed Possible Tools Needed Adjusting AlignmentAdjusting Bent Spreader/Riving Knife Follow Checking Alignment, Steps 1-4, onOptional Table Insert D3697-Standard Zero-Clearance InsertNew Parts Description=\FjVainBVXcZhVcYIddah Page Contents Introduction Woodstock Technical SupportIntroduction Introduction Controls and Features Safety Standard Safety InstructionsAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Table Saws Preventing Kickback Below are tips to avoid the most common causes of kickbackDo not stand directly behind Blade when making a cut Protecting Yourself from KickbackCommon Terms W1761 Electrical Specifications W1761 220V Single-Phase OperationExtension Cords Phase Converter W1762 220V 3-Phase OperationW1762 440V 3-Phase Operation Electrical SpecificationsDescription Qty Items Needed for Set UpUnpacking Immediately discard all Plastic bags and packFence Inventory InventoryMachine Inventory Box Inventory FigureFence Rail Inventory Extension Table InventoryCleaning Machine Machine PlacementTo install the front and rear rails, do these steps Extension TableLeveling main extension table Support Leg Hex Nut Foot Support leg fastened to main Extension table Arbor To install the blade, do these stepsSaw Blade To change the arbor, do these stepsTable Insert To install and adjust the table insert, do these stepsTo install the blade guard, do these steps Blade Guard & SplitterTo install the riving knife, do these steps SplitterTo install the miter gauge, do these steps ON/OFF SwitchTo install the switch, do these steps Miter GaugeDust Collection Recommended AdjustmentsRecommended adjustment checklist Recommended CFM at Dust PortTest Run To test run the machine, do these stepsGeneral Basic ControlsCrosscut blade features see Figure Disabling On/Off SwitchRipping blade features see Figure Blade SelectionLaminate blade features see Figure Combination blade features see FigureDado Blades see Figure Non-Through Cuts Workpiece InspectionNon-Through Through Cuts Through CutsRipping Typical ripping operationTo make a crosscut using the miter gauge, do these steps CrosscuttingBlade Tilt & Bevel Cuts Miter CutsTo perform a miter cut, do these steps Dado Cutting To use a stacked or wobble dado blade, do these stepsDisconnect the SAW from Power Rabbet Cutting To cut rabbets with the dado blade, do these stepsTo cut rabbets with the standard blade, do these steps First cut to create a rabbet With a standard bladeResawing Resaw BarrierAuxiliary Fence To build the auxiliary fence, do these stepsResawing Operations To perform resawing operations, do these stepsTable Saw Accessories D3585 Bore General Purpose D3586 Fine Finishing D3587 100 Operations Daily Check CleaningLubrication Weekly CheckTroubleshooting Motor & ElectricalOperations W1761/W1762 12 Table Saw with Riving KnifeReplacing Flat Belt To remove the flat belt, do these stepsTo install the new belt, do these steps Deflect it no more than 1⁄8To set the 90 stop bolt, do these steps Blade Tilt StopsTo set the 45 stop bolt, do these steps Digital Readout To adjust the tilt indicator arrow, do these stepsTo set the digital readout, do these steps Example of adjusting blade to Miter slot Miter Slot to Blade ParallelismTo adjust the blade by moving the table, do these steps Blade AlignmentSquare and Height Adjusting FenceClamping Pressure and Parallelism Miter gauge diagram Switch W1761 magnetic switchW1761 Wiring Diagram See FigureW1762 magnetic switch prewired to 220V, 3-phase W1762 Electrical ComponentsW1762 Wiring Diagram 220V, 3-Phase W1762 Wiring Diagram 440V, 3-Phase Blade Guard Assembly Blade Guard Assembly Parts List PartsFence Assembly Fence Assembly Parts List Miter Gauge Assembly Miter Gauge Parts List Main Table, Motor & Cabinet Main Table, Motor & Cabinet Parts List MotoraccesscoverMitergaugemountingbracket Extension Table Assembly Extension Table Parts List Label Placement Warranty Page Page Warranty Registration CommentsBOX BELLINGHAM, WA