Woodstock W1761, W1762 Rabbet Cutting, To cut rabbets with the dado blade, do these steps

Page 50

W1761/W1762 12" Table Saw with Riving Knife

OPERATIONS

Rabbet Cutting

Commonly used in furniture joinery, a rabbet is an L- shaped groove cut in the edge of the workpiece. Rabbets can be cut with either a dado blade or a standard saw blade.

Rabbet cutting on the edge of the workpiece requires a sacrificial fence attachment as shown in Figure 51.

To cut rabbets with the dado blade, do these steps:

1.DISCONNECT THE SAW FROM POWER!

2.Make the sacrificial fence the same length as the fence and 3⁄4" thick.

3.Attach it to the fence with screws or clamps as shown in Figure 51, making sure they are all secure and tight.

4.Adjust the fence, turn the saw ON, raise the blade into the sacrificial fence to the height needed for the rabbeting operation, and turn the saw OFF.

5.Align the workpiece to perform the cutting operation as shown in Figure 52.

The danger of kickback increases relative to the depth and width of a cut. Reduce the risk of kickback by making multiple passes to achieve the desired depth of cut. Failure to follow these warnings could result in serious personal injury.

6.Reconnect the saw to the power source and turn the saw ON.

7.When the blade has reached full speed, perform a test cut with a scrap piece of wood.

8.If the cut is satisfactory, repeat the cut with the final workpiece.

��

��

��

��

Figure 51. Sacrificial fence.

You may experience kickback during this procedure. Stand to the side of the blade and wear safety glasses or a face shield to prevent injury when cutting rabbets.

Always use push sticks, featherboards, push paddles and other safety accessories whenever possible to increase safety and control during operations which require that the blade guard and splitter must be removed from the saw. ALWAYS replace the blade guard after dadoing is complete.

��

��

��

Figure 52. Rabbet cutting.

-36-

Image 50

Contents Table SAW with Riving Knife Important Changes to Assembly Inventory DifferencesBlade Size Requirements Blade InstallationBlade Requirements Spreader Blade GuardGuard Installing Blade Guard & Spreader Location to secure blade guard ScrewAnti-Kickback Pawls To remove the pawls, do these stepsWhen to Use the Blade Guard When Not to Use the Blade GuardWhen Not to Use the Riving Knife Installing Riving KnifeWhen to Use the Riving Knife Riving KnifeTools Needed Spreader or Riving Knife AlignmentChecking Alignment Possible Tools Needed Adjusting AlignmentAdjusting Bent Spreader/Riving Knife Follow Checking Alignment, Steps 1-4, onOptional Table Insert D3697-Standard Zero-Clearance InsertNew Parts Description=\FjVainBVXcZhVcYIddah Page Contents Introduction Woodstock Technical SupportIntroduction Introduction Controls and Features Safety Standard Safety InstructionsAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Table Saws Preventing Kickback Below are tips to avoid the most common causes of kickbackDo not stand directly behind Blade when making a cut Protecting Yourself from KickbackCommon Terms Extension Cords W1761 220V Single-Phase OperationW1761 Electrical Specifications Phase Converter W1762 220V 3-Phase OperationW1762 440V 3-Phase Operation Electrical SpecificationsDescription Qty Items Needed for Set UpUnpacking Immediately discard all Plastic bags and packFence Inventory InventoryMachine Inventory Box Inventory FigureFence Rail Inventory Extension Table InventoryCleaning Machine Machine PlacementTo install the front and rear rails, do these steps Extension TableLeveling main extension table Support Leg Hex Nut Foot Support leg fastened to main Extension table Arbor To install the blade, do these stepsSaw Blade To change the arbor, do these stepsTable Insert To install and adjust the table insert, do these stepsTo install the blade guard, do these steps Blade Guard & SplitterTo install the riving knife, do these steps SplitterTo install the miter gauge, do these steps ON/OFF SwitchTo install the switch, do these steps Miter GaugeDust Collection Recommended AdjustmentsRecommended adjustment checklist Recommended CFM at Dust PortTest Run To test run the machine, do these stepsGeneral Basic ControlsCrosscut blade features see Figure Disabling On/Off SwitchRipping blade features see Figure Blade SelectionDado Blades see Figure Combination blade features see FigureLaminate blade features see Figure Non-Through Cuts Workpiece InspectionNon-Through Through Cuts Through CutsRipping Typical ripping operationTo make a crosscut using the miter gauge, do these steps CrosscuttingTo perform a miter cut, do these steps Miter CutsBlade Tilt & Bevel Cuts Dado Cutting To use a stacked or wobble dado blade, do these stepsDisconnect the SAW from Power Rabbet Cutting To cut rabbets with the dado blade, do these stepsTo cut rabbets with the standard blade, do these steps First cut to create a rabbet With a standard bladeResawing Resaw BarrierAuxiliary Fence To build the auxiliary fence, do these stepsResawing Operations To perform resawing operations, do these stepsTable Saw Accessories D3585 Bore General Purpose D3586 Fine Finishing D3587 100 Operations Daily Check CleaningLubrication Weekly CheckTroubleshooting Motor & ElectricalOperations W1761/W1762 12 Table Saw with Riving KnifeReplacing Flat Belt To remove the flat belt, do these stepsTo install the new belt, do these steps Deflect it no more than 1⁄8To set the 45 stop bolt, do these steps Blade Tilt StopsTo set the 90 stop bolt, do these steps To set the digital readout, do these steps To adjust the tilt indicator arrow, do these stepsDigital Readout Example of adjusting blade to Miter slot Miter Slot to Blade ParallelismTo adjust the blade by moving the table, do these steps Blade AlignmentClamping Pressure and Parallelism Adjusting FenceSquare and Height Miter gauge diagram Switch W1761 magnetic switchW1761 Wiring Diagram See FigureW1762 magnetic switch prewired to 220V, 3-phase W1762 Electrical ComponentsW1762 Wiring Diagram 220V, 3-Phase W1762 Wiring Diagram 440V, 3-Phase Blade Guard Assembly Blade Guard Assembly Parts List PartsFence Assembly Fence Assembly Parts List Miter Gauge Assembly Miter Gauge Parts List Main Table, Motor & Cabinet Main Table, Motor & Cabinet Parts List MotoraccesscoverMitergaugemountingbracket Extension Table Assembly Extension Table Parts List Label Placement Warranty Page Page Warranty Registration CommentsBOX BELLINGHAM, WA