Woodstock W1762, W1761 owner manual Saw Blade, Arbor, To install the blade, do these steps

Page 35

W1761/W1762 12" Table Saw with Riving Knife

Saw Blade

Review this section, even if your saw blade came pre- installed.

To install the blade, do these steps:

1.DISCONNECT THE SAW FROM POWER!

2.Remove the table insert, blade guard, and splitter–if previously installed.

3.Use the arbor wrenches to loosen and remove the arbor nut, flange, and blade.

Note: The arbor nut has right hand threads; turn it counterclockwise to loosen.

4.Slide the new blade over the arbor with the teeth facing the front of the saw, as shown in Figure 24.

5.Re-install the arbor flange and the arbor nut, and tighten them against the blade with the wrench included with the saw. DO NOT overtighten.

The saw blade is extremely sharp. Wear gloves and use extra care when handling the blade or working near it. Serious injury is possible.

	Teeth Direction	SET
Front Of Saw	& Blade Rotation
Front Of Saw
		UP

Figure 24. Correct blade direction.

Arbor

A 1" or 5/8" arbor can be installed on the table saw, depend- ing upon the arbor size of the blade you want to install.

To change the arbor, do these steps:

1.DISCONNECT THE SAW FROM POWER!

2.Remove the table insert, blade guard and splitter or riving knife, arbor nut, arbor flange, and blade.

3.Raise the arbor all the way up.

4.Hold the arbor shaft with the arbor wrench and, using a 5mm hex wrench, remove the cap screw from the end of the arbor, as shown in Figure 25. Note: Gently tap the arbor with a rubber mallet to unseat it if it is hard to remove.

5.Slide the arbor out of the arbor shaft and reinstall the new arbor in the same manner that the old one was removed. Make sure the new arbor is securely tight- ened in the arbor shaft before reinstalling the blade.

-21-

Arbor

	Cap Screw	Arbor
	Cap Screw	Shaft
		Shaft
	Figure 25. Removing arbor.

Image 35

Contents Table SAW with Riving Knife Inventory Differences Important Changes to AssemblyBlade Size Requirements Blade InstallationBlade Requirements Spreader Blade GuardGuard Location to secure blade guard Screw Installing Blade Guard & SpreaderTo remove the pawls, do these steps Anti-Kickback PawlsWhen Not to Use the Blade Guard When to Use the Blade GuardRiving Knife Installing Riving KnifeWhen to Use the Riving Knife When Not to Use the Riving KnifeTools Needed Spreader or Riving Knife AlignmentChecking Alignment Follow Checking Alignment, Steps 1-4, on Adjusting AlignmentAdjusting Bent Spreader/Riving Knife Possible Tools NeededD3697-Standard Zero-Clearance Insert Optional Table InsertDescription New Parts=\FjVainBVXcZhVcYIddah Page Contents Woodstock Technical Support IntroductionIntroduction Introduction Controls and Features Standard Safety Instructions SafetyAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Table Saws Below are tips to avoid the most common causes of kickback Preventing KickbackProtecting Yourself from Kickback Do not stand directly behind Blade when making a cutCommon Terms Extension Cords W1761 220V Single-Phase OperationW1761 Electrical Specifications Electrical Specifications W1762 220V 3-Phase OperationW1762 440V 3-Phase Operation Phase ConverterImmediately discard all Plastic bags and pack Items Needed for Set UpUnpacking Description QtyBox Inventory Figure InventoryMachine Inventory Fence InventoryExtension Table Inventory Fence Rail InventoryMachine Placement Cleaning MachineExtension Table To install the front and rear rails, do these stepsLeveling main extension table Support Leg Hex Nut Foot Support leg fastened to main Extension table To change the arbor, do these steps To install the blade, do these stepsSaw Blade ArborBlade Guard & Splitter To install and adjust the table insert, do these stepsTo install the blade guard, do these steps Table InsertSplitter To install the riving knife, do these stepsMiter Gauge ON/OFF SwitchTo install the switch, do these steps To install the miter gauge, do these stepsRecommended CFM at Dust Port Recommended AdjustmentsRecommended adjustment checklist Dust CollectionTo test run the machine, do these steps Test RunBasic Controls GeneralBlade Selection Disabling On/Off SwitchRipping blade features see Figure Crosscut blade features see FigureDado Blades see Figure Combination blade features see FigureLaminate blade features see Figure Through Cuts Workpiece InspectionNon-Through Through Cuts Non-Through CutsTypical ripping operation RippingCrosscutting To make a crosscut using the miter gauge, do these stepsTo perform a miter cut, do these steps Miter CutsBlade Tilt & Bevel Cuts To use a stacked or wobble dado blade, do these steps Dado CuttingDisconnect the SAW from Power To cut rabbets with the dado blade, do these steps Rabbet CuttingFirst cut to create a rabbet With a standard blade To cut rabbets with the standard blade, do these stepsResaw Barrier ResawingTo build the auxiliary fence, do these steps Auxiliary FenceTo perform resawing operations, do these steps Resawing OperationsTable Saw Accessories D3585 Bore General Purpose D3586 Fine Finishing D3587 100 Operations Weekly Check CleaningLubrication Daily CheckMotor & Electrical TroubleshootingW1761/W1762 12 Table Saw with Riving Knife OperationsTo remove the flat belt, do these steps Replacing Flat BeltDeflect it no more than 1⁄8 To install the new belt, do these stepsTo set the 45 stop bolt, do these steps Blade Tilt StopsTo set the 90 stop bolt, do these steps To set the digital readout, do these steps To adjust the tilt indicator arrow, do these stepsDigital Readout Miter Slot to Blade Parallelism Example of adjusting blade to Miter slotBlade Alignment To adjust the blade by moving the table, do these stepsClamping Pressure and Parallelism Adjusting FenceSquare and Height Miter gauge diagram W1761 magnetic switch SwitchSee Figure W1761 Wiring DiagramW1762 Electrical Components W1762 magnetic switch prewired to 220V, 3-phaseW1762 Wiring Diagram 220V, 3-Phase W1762 Wiring Diagram 440V, 3-Phase Parts Blade Guard Assembly Blade Guard Assembly Parts ListFence Assembly Fence Assembly Parts List Miter Gauge Assembly Miter Gauge Parts List Main Table, Motor & Cabinet Motoraccesscover Main Table, Motor & Cabinet Parts ListMitergaugemountingbracket Extension Table Assembly Extension Table Parts List Label Placement Warranty Page Page Comments Warranty RegistrationBOX BELLINGHAM, WA