Emerson LK803, LK801, LK800, LK37, F468 owner manual Safety Instructions, Assembly and Installation

!WARNING

Safety Instructions

To avoid fire, shock, and serious personal injury, follow all instructions carefully.

1.Read your Owner's Manual carefully before installing the light fixture. Retain Owner's Manual for future reference.

2.Be careful of the fan and blades when cleaning, painting, or working near the fan. Before installing or servicing the light fixture or ceiling fan, switch power off at service panel and lock service panel disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a warning device, such as a tag, to the service panel.

3.Do not exceed the wattage indicated on fixture.

ADDITIONAL SAFETY INSTRUCTIONS FOR INSTALLATION

1.To avoid possible electrical shock be sure electricity is turned off at the main fuse or circuit breaker box before wiring.

2.Make certain no bare wires are exposed outside the wire connectors.

3.All wiring must conform to national and local electrical codes.

4.Follow the recommended instructions for the proper method of wiring your new light fixture. If you feel you do not have enough electrical wiring knowledge or experience, have your light fixture installed by a licensed electrician. Any electrical work not described in this manual should be performed by a licensed electrician.

WARNING: To reduce the risk of possible fire and electrical shock, install only on Emerson “CF” and “F” Series Ceiling Fans. This light kit is not to be used with CF652, CF653, CF670, CF680, CF742 and CF2000 Series Ceiling Fans installed in damp or wet locations.

Assembly and Installation

7.Insert the black and white wires through the lockwasher (8) and hex nut (9) (supplied). Firmly tighten the hex nut to secure the light fitter to the switch cup.

8.Connect the white wire from the switch cup to the white wire of the light fitter (Figure 2). Connect the blue wire from the switch cup to the black wire of the light fitter. Use listed wire connectors (previously removed in step 5) to make connections (Figures 2 and 3).

(4) MOTOR	(2) COVER PLATE
CONNECTOR	(5) SWITCH CUP
	CONNECTOR
	(6) WIRE
BLUE WIRE	CONNECTORS
BLACK WIRE	WHITE WIRES
(3) SCREWS	FAN SWITCH
(9) HEX NUT
	CHAIN
(1) SWITCH CUP
	(8) LOCKWASHER
	(7) LIGHT FITTER

11.Position the cup/light fitter (1)(7) on the cover plate (2) and install the three screws (3) that were previously removed in step 2 and tighten securely.

12.Proceed to “Installation of “Glass Shades” section.

Installation on Emerson Fans Having Two-Piece Die-Cast Switch Housings

1.Remove all parts and parts packages from carton.

2.Remove the cover (5) from the switch housing (1) by removing the two outer screws (2). (See Figure 4.)

3.Remove the center screw (4) from the cover (5). Insert the black and white wires from the light kit fitter (6) through the hole and thread the switch housing cover tightly onto the light kit fitter.

4.Insert the black and white wires through

the lockwasher (8) and hex nut (7)

supplied. Firmly tighten the hex nut to

secure the light kit fitter to the switch

!WARNING

Do not install or use the light fixture if any part is missing or damaged. Call toll-free:

1-800-654-3545

!WARNING

To avoid possible electrical shock, be sure electricity is turned off at the main fuse or circuit breaker box before wiring.

4.Remove the center screw (6) from the switch cup (Figure 1).

5.Carefully locate the white and blue wires (labeled either "L" or "LIGHT") in the switch cup and remove the wire connectors from the wires.

6.Insert the black and white wires from the light fitter (7) through the center hole in the switch cup (Figure 2) and thread the switch cup onto the light fitter. Hold wires taut while installing switch cup to prevent the wires from twisting.

NOTE: YOUR FITTER MAY NOT LOOK THE SAME AS

Figure 2 THE ONE IN THIS ILLUSTRATION.

HOWEVER, IT INSTALLS IN A SIMILAR MANNER.

!WARNING

To avoid possible fire or electrical shock, make certain no bare wire strands are exposed outside wire connectors.

housing cover (5).

5.Carefully locate the white and blue

wires (labeled either “L” or “LIGHT”) in

the switch housing and remove the

wire connectors (3) from the wires.

6. Connect the white wire from the ceiling

fan to the white wire of the light fitter

(6). Connect the blue wire from the

ceiling fan to the black wire of the light

fitter. Use listed wire connectors

(previously removed in step 3) to make

connections. (Figures 3 and 4.)

7. Carefully tuck all wires and splices into

the switch housing (1).

Installation on Emerson Fans

Having Modular Switch Cup with

Center Screw

1.Remove all parts and parts packages from the carton.

2.Remove the switch cup (1) from the cover plate (2) by removing the three screws (3) around the side of the switch cup (Figure 1).

3.Disconnect the motor connector (4) from the switch cup connector (5) (Figure 1).

(4) MOTOR	(2) COVER PLATE
CONNECTOR
(3) SCREWS	(5) SWITCH CUP
	CONNECTOR
	FAN SWITCH
(1) SWITCH	CHAIN
CUP
(6) CENTER SCREW

Figure 1

Figure 3

9.Carefully tuck all wires and splices into the switch cup (1). (Figure 2.)

10.Connect the motor connector (4) to the switch cup connector (5).

8. Attach the cover/light fitter (5) (6) to the

switch assembly housing (1) using the

two screws (2) that were removed in

Step 2) (Figure 4.)

!WARNING

To avoid possible fire or electric shock, be careful not to pinch wires between switch housing and light fitter.

2 3