RIDGID R841150 manual Operation

Page 10

OPERATION

WARNING:

Do not allow familiarity with the hammer drill to make you careless. Remember that a careless frac- tion of a second is sufficient to inflict severe injury.

CHARGING BATTERY PACK

The battery pack for this tool has been shipped in a low charge condition to prevent possible problems. Therefore, you should charge it until the light on front of charger changes from flashing green to continuous green.

Note: Batteries will not reach full charge the first time they are charged. Allow several cycles (drilling followed by recharging) for them to become fully charged. This is nominal for nickel-cadmium batteries.

TO CHARGE

Charge battery pack only with the charger provided.

Make sure power supply is normal house voltage, 120 volts, 60 Hz, AC only.

Connect the charger to a power supply.

Attach battery pack to charger by aligning raised ribs on battery pack with grooves in charger, then slide battery pack onto charger. See Figure 2.

After normal usage, 30 minutes of charging time is required to be fully charged.

The battery pack will become slightly warm to the touch while charging. This is normal and does not indicate a problem.

Do not place charger in an area of extreme heat or cold. It will work best at normal room temperature.

When the batteries become fully charged, unplug your charger from power supply and remove the battery pack.

IMPORTANT INFORMATION FOR RECHARG- ING HOT BATTERY PACK

When using this drill continuously, the batteries in the battery pack will become hot. The battery pack for this tool will charge more rapidly and efficiently when at a cooled temperature.

The internal fan for this charger will automatically turn on when a hot battery pack is inserted. Air circulates through the battery, bringing it to optimum charging temperature, decreasing the time required to begin fast charging the pack, and extending the life of the battery.

When the battery pack becomes discharged and is hot, the green LED will be off and the red LED will begin flashing.

When the battery pack cools down to approximately 104°F (40°C), the charger will automatically begin fast charge mode.

If the Red LED continues to flash for more than 90 minutes, and the green LED remains off, this may indicate a dam- aged battery that will not charge.

30 min

?

30 min

Fig. 2

IMPORTANT INFORMATION FOR RECHARG- ING COOL BATTERY PACK

If battery pack is below normal temperature range, the red LED will begin flashing and the green LED will be off. When the battery warms to a temperature of more than 41°F (5°C), the charger will automatically begin fast charge mode.

Note: Refer to "CHARGING BATTERY PACK" for normal recharging of batteries. If the charger does not charge your battery pack under normal circumstances, return both the battery pack and charger to your nearest repair center for electrical check. For the location of your nearest repair center, please call 1-866-539-1710.

KEEPING THE CHARGER VENTS CLEAN

The fan in this charger will perform more efficiently if the air vents and ports are kept free of dust or other debris. Peri- odically check the air vents, and using a fine brush, whisk dust or debris away from the air vents and ports.

CAUTION:

To prevent damage to battery pack, remove battery pack from charger immediately if no LED comes on. Return battery pack and charger to your near- est service center for checking or replacing. Also, if you are removing battery pack from charger and no LEDs are on, return both battery pack and charger to your nearest service center. Do not insert an- other battery pack into charger. A damaged charger may damage a battery pack.

10

Image 10
Contents OPERATOR’S Manual Table of Contents IntroductionGeneral Safety Rules Model Battery Pack ChargerSpecific Safety Rules ServiceImportant Safety Instructions for Charger Symbols Symbol Name DESIGNATION/EXPLANATIONFeatures Battery Pack Dual Port Charger Depth Gage RODInstructions UnpackingPacking List Operation LED Function of Charger Power Indicator EvaluateFull Indicator OFFApplications To Install Battery PackTo Remove Battery Pack Variable SpeedReversible TWO-SPEED Gear TrainRemoving Bits Installing BitsUnlock Release Lock Tighten To Adjust Torque Installing Depth Gage RODAdjustable Torque Clutch To Increase TorqueDrilling Metal Drilling To Adjust Drilling or Hammer ModeWood Drilling Masonry DrillingGeneral MaintenanceChuck Removal Batteries Battery Pack Removal Preparation for RecyclingTo Retighten a Loose Chuck CYCWhat is Covered Under the Limited Three Year Warranty WarrantyDAY Satisfaction Guarantee Policy HOW to Obtain Service What is not CoveredPage Volt Mm Hammer Drill R841150 Two Speed/Reversible

R841150 specifications

The RIDGID R841150 is a powerful and versatile 18V cordless hybrid fan, designed to deliver exceptional airflow and functionality for both professional and DIY users. With its robust construction and innovative features, the R841150 stands out in the crowded market of cordless tools, making it a must-have for any toolkit.

One of the most notable features of the R841150 is its hybrid capability, which allows the fan to operate using either a RIDGID 18V battery or a standard AC power outlet. This flexibility ensures that users can rely on the fan in various situations, whether working on a job site without access to electricity or needing a steady airflow indoors.

The fan boasts a powerful motor that produces impressive airflow, making it suitable for cooling, ventilation, and drying applications. With multiple speed settings, users can easily adjust the airflow to meet their specific needs, ensuring comfort and efficiency. This versatility makes the R841150 ideal for a range of environments, including construction sites, workshops, and outdoor events.

Portability is a key characteristic of the RIDGID R841150. Weighing in at just under eight pounds, the fan is lightweight and equipped with a built-in handle, allowing for easy transportation from one location to another. Additionally, the fan features a 360-degree rotating head, enabling users to direct airflow precisely where it's needed, enhancing its usability in tight or awkward spaces.

Durability is another cornerstone of the RIDGID brand, and the R841150 is no exception. Constructed from high-quality materials, this fan is designed to withstand the rigors of daily use. Its robust housing protects internal components from damage, ensuring longevity even in demanding conditions.

The integrated LED light is a thoughtful addition, providing illumination in low-light situations. This feature enhances the fan’s overall functionality, making it a valuable tool not just for ventilation but also for lighting spaces during evenings or in dark corners.

In summary, the RIDGID R841150 hybrid fan combines versatility, portability, and durability, making it an essential tool for various applications. Its powerful motor, adjustable speed settings, and 360-degree rotation, along with hybrid operation, make it an excellent choice for both professionals and DIY enthusiasts looking to enhance their work experience.