RIDGID TS 2400 manual Lever...Locks the sliding table exten- sion

Page 16

Getting to Know Your Table Saw

1.Rip Fence...is locked in place by pushing the lock lever down until the lever rests on the stop. To move the fence, lift the lock lever and grasp the fence with one hand at the front. “T” slots are provided in the rip fence for attaching a wood facing when using the dado head, or molding head.

2.Micro-Adjust Rip Fence...allows the operator to accurately adjust the rip fence using only one hand. To move the fence push in on the micro-adjust knob and rotate.

3.Table Extension Lock

Lever...Locks the sliding table exten- sion.

4.Sliding Table Extension...provides additional working surface to support large workpieces and increase rip capability.

5.Rip Fence Storage...holds the fence when not being used.

6.Miter Gauge Storage...holds the miter gauge when not being used.

7.Two-Piece Base...supports table. For additional stability, holes are pro- vided in base to bolt the saw to a workbench or stand or sawhorses.

8.Blade Bevel Scale...shows the degree the blade is beveled.

9.Elevation/Bevel Handwheel

a.Elevates or lowers the blade. Turn the knob clockwise to ele- vate, counterclockwise to lower.

b.Use the knob to quickly tilt the blade from 0° to 45°. Rotate the outer hub for finer adjustments.

When the blade is tilted to the left as far as it will go, it should be at 45° to the table and the bevel

pointer should point to 45°. NOTE: There are limit stops inside the saw which prevent the blade from tilting beyond 45° to the left and 0°. (See “Adjust- ments and Alignments” section “Blade Bevel, or Squareness of Blade to Table”).

10.Blade Elevation Lock Knob...locks the blade at the desired height.

11.Blade Bevel Lock Lever...locks the blade in the desired bevel position. Lift the lever to the right to unlock push to the left to lock.

12.On-Off Switch

CAUTION: Before turning switch “ON”, make sure the blade guard is correctly installed and operating properly.

The On-Off Switch has a locking fea- ture. This feature is intended to help prevent unauthorized and possible hazardous use by children and oth- ers.

a. To turn saw ON, insert key, stand to either side of the blade, never in line with it, place finger under switch lever and pull end of lever out.

After turning switch ON, always allow the blade to come up to full speed before cutting. Do not cycle the motor switch on and off rapidly, as this may cause the sawblade to loosen. In the event this should ever occur, allow the sawblade to come to a complete stop and retighten the arbor nut normally, not excessively. Never leave the saw while the power is ON.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Page Table of Contents Safety Instructions For Table Saw Before Using The SawTo reduce the risk of injury from unexpected saw movement Reduce the Risk of Dangerous EnvironmentInspect your saw Inspect Your Blade Inspect your work areaSafety Instructions For Table Saws Dress for safetyPlan your work Inspect your workpieceReduce the Risk of Accidental Starting Keep Children AwayDon’t Force Tool Before freeing jammed materialTo reduce the risk of throwback of cut off pieces To remove loose pieces beneath or trapped inside the guardBefore Leaving The Saw Before StartingGlossary of Terms for Woodworking While CuttingPush Stick Push BlockRabbet ResinMotor Specifications and Electrical Requirements Motor Specifications and Electrical Requirements Wire Sizes Thermal Overload ProtectorThermal Overload Device Extension Gauge Cord LengthUnpacking and Checking Contents Getting to Know Your Table Saw Lever...Locks the sliding table exten- sion Key Switch Table...provides working surface to support workpiecesSawdust Ejection Port Wrench/Blade Storage Rip Fence StorageMiter Gauge Storage Guard Latches Blade Wrench Wing Nut Fence Miter GaugeAlignment Tools NeededRemove Foam Motor Support Checking Table InsertTo check for parallelism Marked ToothSawbladeCombination Miter Gauge Square GrooveAlignment Checking Blade Tilt, or Squareness of Blade to Table To Check For Squareness, 90 PositionIf blade is square to table Square Blade Pointer at Position StopscrewIf blade is 45 to table To check for alignment, 45 PositionScale Screws Stopscrew Aligning Rip Fence Guide Bars Adjusting Rip Fence Guide BarsPages Rip Scale Hold Down Aligning Sliding Table Extension Rip Fence Alignment AdjustmentCombination Square Rip Fence Lock Lever Adjustment Adjusting Rip IndicatorAdjusting Nut Rip IndicatorInstalling Blade Guard If the sliding table extension moves when lockedChecking Sliding Table Extension Hex Locking Front Hex Nut CouplingAligning Blade Guard WoodKerf Spreader Blade Do not loosen other screws. ThisRemoving and Installing Sawblade Miter Gauge Alignment Adjusting Bevel Lock Marking Ind-I-Cut UsingMarking the Ind-I-Cut Blade Tilt Lock NutWorkbench Mounting Using Hardware Table Saw Mounting ProceduresFront of Table Saw Diagram of Workbench Mounting Holes Mounting Your SawWorkbench Mounting Using C Clamps Supporting Table Saw with SawhorsesSafety Instructions for Basic Saw Operations Before Each Use Inspect your sawPlan your cut Whenever Sawblade Is Spinning Work Feed Devices Push Stick Push Block For Use with Auxiliary FenceAuxiliary Fence Fence Facing Using the Miter Gauge Additional Safety Instructions for CrosscuttingBasic Saw Operations CrosscuttingRepetitive Crosscutting Clamp Wood Block Cut Off PieceBevel Crosscutting Miter CrosscuttingCompound Crosscutting Additional Safety Instructions for Rip Cuts Using the Rip FenceWhile Thru sawing Once the trailing end is on the table RippingBlade Path Auxiliary Fence Clamp Bevel Ripping Narrow WorkPush Block Workpiece Auxiliary Fence Baffle Using Featherboards for Thru Sawing Might otherwise pinch the bladeKerf and cause a kickback PushUsing Featherboards for Non-Thru Sawing Install blade guard immediately Using Carbide Tipped BladesResawing KickbackDadoing Dado InsertSaw ArborRabbeting Ploughing and MoldingMolding Molding Auxiliary FenceAdjusting Nylon Set Screw MaintenanceMaintaining Your Table Saw Ridgid Recommends the Following Accessories Replacing Carbon BrushesLubrication SKU NoGeneral TroubleshootingTrouble Probable Cause Remedy Motor Trouble Probable Cause RemedyRepair Parts Parts List for Ridgid 10 Inch Table Saw Model No. TS24001Always Order by Part Number not by Key Number Key DescriptionRepair Parts Parts List for Ridgid 10 Inch Table Saw Model TS24001 Key Description 827483 Cover BladeMiter Gauge Assembly Always Order by Part Number Not by Key Number DescriptionFence Assembly Guard Assembly Page Page Page RIDGID, INC Stock No. TS2400 Model No. TS24001 Serial No
Top Page Image Contents