RIDGID TS 2400 Miter Gauge Assembly, Always Order by Part Number Not by Key Number Description

Page 62

Repair Parts

Parts List for RIDGID 10 Inch Table Saw

Model No. TS24001

RIDGID parts are available on-line at www.ridgidparts.com

Figure 3 - Miter Gauge Assembly

		4
15	14	5

12	7
	7
	11
	8
	9
	10

Always Order by Part Number - Not by Key Number

Key	Part No.	Description
No.	Part No.	Description
No.


–	830338	Miter Gauge Asm. Complete
1	826506-1	Knob
2	821063-5	* Washer 8 x 23 x 1.8
3	826663	Gauge, Miter
4	824723-1	* Screw, Pan Hd. 8/32 x 5/16
5	123069-1	Indicator
6	830351	Block, Miter Gauge Indicator
7	830352	Pin, Miter
8	140755-15	* Lockwasher #8
9	824723	* Screw, Pan Hd 8-32 x 5/8
10	818470-4	Screw Flat Hd. M6 x 1.0-16
11	830350	Rod, Miter Gauge
12	830354	Screw, Flat Head
13	830353	Washer, “T” Slot
14	134530	* Nut Hex 6-32
15	809813-4	Screw Pan Hd. 6-32 x 5/8
16	818471-6	Screw, Set 5 x 0.8-5

* Standard Hardware Item - May be purchased locally

Image 62

Contents Page Table of Contents Safety Instructions For Table Saw Before Using The SawInspect your saw Reduce the Risk of Dangerous EnvironmentTo reduce the risk of injury from unexpected saw movement Inspect Your Blade Inspect your work areaPlan your work Safety Instructions For Table SawsDress for safety Inspect your workpieceDon’t Force Tool Reduce the Risk of Accidental StartingKeep Children Away Before freeing jammed materialBefore Leaving The Saw To reduce the risk of throwback of cut off piecesTo remove loose pieces beneath or trapped inside the guard Before StartingGlossary of Terms for Woodworking While CuttingRabbet Push StickPush Block ResinMotor Specifications and Electrical Requirements Motor Specifications and Electrical Requirements Thermal Overload Device Wire SizesThermal Overload Protector Extension Gauge Cord LengthUnpacking and Checking Contents Getting to Know Your Table Saw Lever...Locks the sliding table exten- sion Key Switch Table...provides working surface to support workpiecesSawdust Ejection Port Miter Gauge Storage Wrench/Blade StorageRip Fence Storage Guard Latches Blade Wrench Wing Nut Fence Miter GaugeRemove Foam Motor Support AlignmentTools Needed Checking Table InsertCombination Miter Gauge To check for parallelismMarked ToothSawblade Square GrooveAlignment If blade is square to table Checking Blade Tilt, or Squareness of Blade to TableTo Check For Squareness, 90 Position Square Blade Pointer at Position StopscrewScale Screws Stopscrew To check for alignment, 45 PositionIf blade is 45 to table Pages Rip Scale Hold Down Adjusting Rip Fence Guide BarsAligning Rip Fence Guide Bars Combination Square Rip Fence Alignment AdjustmentAligning Sliding Table Extension Adjusting Nut Rip Fence Lock Lever AdjustmentAdjusting Rip Indicator Rip IndicatorChecking Sliding Table Extension Installing Blade GuardIf the sliding table extension moves when locked Hex Locking Front Hex Nut CouplingKerf Spreader Blade Aligning Blade GuardWood Do not loosen other screws. ThisRemoving and Installing Sawblade Miter Gauge Alignment Marking the Ind-I-Cut Adjusting Bevel LockMarking Ind-I-Cut Using Blade Tilt Lock NutFront of Table Saw Diagram of Workbench Mounting Holes Workbench Mounting Using HardwareTable Saw Mounting Procedures Mounting Your SawWorkbench Mounting Using C Clamps Supporting Table Saw with SawhorsesSafety Instructions for Basic Saw Operations Before Each Use Inspect your sawPlan your cut Whenever Sawblade Is Spinning Work Feed Devices Push Stick Push Block For Use with Auxiliary FenceAuxiliary Fence Fence Facing Basic Saw Operations Using the Miter GaugeAdditional Safety Instructions for Crosscutting CrosscuttingRepetitive Crosscutting Clamp Wood Block Cut Off PieceCompound Crosscutting Miter CrosscuttingBevel Crosscutting While Thru sawing Using the Rip FenceAdditional Safety Instructions for Rip Cuts Blade Path RippingOnce the trailing end is on the table Push Block Workpiece Auxiliary Fence Baffle Bevel Ripping Narrow WorkAuxiliary Fence Clamp Kerf and cause a kickback Using Featherboards for Thru SawingMight otherwise pinch the blade PushUsing Featherboards for Non-Thru Sawing Resawing Install blade guard immediatelyUsing Carbide Tipped Blades KickbackDadoing Dado InsertSaw ArborRabbeting Ploughing and MoldingMolding Molding Auxiliary FenceMaintaining Your Table Saw MaintenanceAdjusting Nylon Set Screw Lubrication Ridgid Recommends the Following AccessoriesReplacing Carbon Brushes SKU NoTrouble Probable Cause Remedy TroubleshootingGeneral Motor Trouble Probable Cause RemedyRepair Parts Parts List for Ridgid 10 Inch Table Saw Model No. TS24001Always Order by Part Number not by Key Number Key DescriptionRepair Parts Parts List for Ridgid 10 Inch Table Saw Model TS24001 Key Description 827483 Cover BladeMiter Gauge Assembly Always Order by Part Number Not by Key Number DescriptionFence Assembly Guard Assembly Page Page Page RIDGID, INC Stock No. TS2400 Model No. TS24001 Serial No