RIDGID TS 2400 manual Parts List for Ridgid 10 Inch Table Saw Model TS24001

Page 61

Repair Parts

Parts List for RIDGID 10 Inch Table Saw

Model TS24001

RIDGID parts are available on-line at www.ridgidparts.com

Figure 2

Always Order by Part Number - not by Key Number

	Key	Part No.	Description
	No.



	1 827483		Cover Blade

2370625 * Screw Hex Wash Hd 1/4-20 x 1/2

3827619 Plate Bevel Stop

4827540 Support Bevel Indicator

5141594-46 * Screw Soc Cap

1/4-20 x 5/8

6 824334-1 Indicator

7805550-5 * Washer 7/32 x 5/8 x 1/16

8808380-17 * Screw Pan Hd #10 x 3/4

9	827459	Bar Locking
10	827862	Clamp Asm Bevel
11	827522	Pivot Bevel Lock
12	827500	Handle Bevel Lock
13	827519	Mount Front
14	830390	Knob Asm Bevel
15	830391	Handle Asm Elevation
16	37937	* Washer 17/64 x 5/8 x 1/32

17809372-7 * Screw Pan Hd 10-32 x 5/8

18827467 Bushing Trunnion

19829971-9 Shaft Elevation Crank (Includes “O” Rings)

20821421-11 Ring “O” 3/8 x 1/16

21805561-4 Washer .505 x 3/16 x 1/32

22805641-4 Ring Retaining 5133-50

2360136 * Washer 13/64 x 5/8 x 1/32

24827496 Gear Elevation

25	802612-8	Nut Push 3/8
26	830381	Motor Asm

	Key	Part No.	Description
	No.	Part No.	Description
	No.


	27	827863	Screw Set Nylon
			10-32 x 3/4
	28	827864	Nut Hex Nylon 10-32
	29	830412	Arbor Asm

309420474 * Screw Hex Ty T 10/32 x 1/2

31808380-17 * Screw Pan Hd #10 x 3/4

32827476 Chute Sawdust

3360249 * Nut Lock 3/8-16

34	60014	* Washer
		.380 x 47/64 x 3/32
35	827520	Mount Rear
36	827531	Shaft Guide
37	830380	Cradle
38	827529	Shaft Elevation
39	830394	Blade 10" 24T Carb.
40	827465	Collar Blade
41	6362	Nut Arbor
42	830386	Spring
43	816768	Brush
44	826017	Holder Brush
45	828064	Cover Motor Rear
46	828122-1	Screw Wash Hd Cr M4-10
47	809398	Nut Weld
48	830385	Spacer Elev Lock
49	60415	Washer Spring
50	830393	Knob Elevation Lock
51	830392	Knob Swivel
52	830250	Cover, Brush

* Standard Hardware Item - May be purchased locally

61

Image 61

Contents Page Table of Contents Before Using The Saw Safety Instructions For Table SawTo reduce the risk of injury from unexpected saw movement Reduce the Risk of Dangerous EnvironmentInspect your saw Inspect your work area Inspect Your BladeDress for safety Safety Instructions For Table SawsPlan your work Inspect your workpieceKeep Children Away Reduce the Risk of Accidental StartingDon’t Force Tool Before freeing jammed materialTo remove loose pieces beneath or trapped inside the guard To reduce the risk of throwback of cut off piecesBefore Leaving The Saw Before StartingWhile Cutting Glossary of Terms for WoodworkingPush Block Push StickRabbet ResinMotor Specifications and Electrical Requirements Motor Specifications and Electrical Requirements Thermal Overload Protector Wire SizesThermal Overload Device Extension Gauge Cord LengthUnpacking and Checking Contents Getting to Know Your Table Saw Lever...Locks the sliding table exten- sion Table...provides working surface to support workpieces Key SwitchSawdust Ejection Port Rip Fence Storage Wrench/Blade StorageMiter Gauge Storage Guard Latches Blade Wrench Wing Nut Fence Miter GaugeTools Needed AlignmentRemove Foam Motor Support Checking Table InsertMarked ToothSawblade To check for parallelismCombination Miter Gauge Square GrooveAlignment To Check For Squareness, 90 Position Checking Blade Tilt, or Squareness of Blade to TableIf blade is square to table Square Blade Pointer at Position StopscrewIf blade is 45 to table To check for alignment, 45 PositionScale Screws Stopscrew Aligning Rip Fence Guide Bars Adjusting Rip Fence Guide BarsPages Rip Scale Hold Down Aligning Sliding Table Extension Rip Fence Alignment AdjustmentCombination Square Adjusting Rip Indicator Rip Fence Lock Lever AdjustmentAdjusting Nut Rip IndicatorIf the sliding table extension moves when locked Installing Blade GuardChecking Sliding Table Extension Hex Locking Front Hex Nut CouplingWood Aligning Blade GuardKerf Spreader Blade Do not loosen other screws. ThisRemoving and Installing Sawblade Miter Gauge Alignment Marking Ind-I-Cut Using Adjusting Bevel LockMarking the Ind-I-Cut Blade Tilt Lock NutTable Saw Mounting Procedures Workbench Mounting Using HardwareFront of Table Saw Diagram of Workbench Mounting Holes Mounting Your SawSupporting Table Saw with Sawhorses Workbench Mounting Using C ClampsBefore Each Use Inspect your saw Safety Instructions for Basic Saw OperationsPlan your cut Whenever Sawblade Is Spinning Work Feed Devices Push Block For Use with Auxiliary Fence Push StickAuxiliary Fence Fence Facing Additional Safety Instructions for Crosscutting Using the Miter GaugeBasic Saw Operations CrosscuttingClamp Wood Block Cut Off Piece Repetitive CrosscuttingBevel Crosscutting Miter CrosscuttingCompound Crosscutting Additional Safety Instructions for Rip Cuts Using the Rip FenceWhile Thru sawing Once the trailing end is on the table RippingBlade Path Auxiliary Fence Clamp Bevel Ripping Narrow WorkPush Block Workpiece Auxiliary Fence Baffle Might otherwise pinch the blade Using Featherboards for Thru SawingKerf and cause a kickback PushUsing Featherboards for Non-Thru Sawing Using Carbide Tipped Blades Install blade guard immediatelyResawing KickbackDado InsertSaw Arbor DadoingPloughing and Molding RabbetingMolding Auxiliary Fence MoldingAdjusting Nylon Set Screw MaintenanceMaintaining Your Table Saw Replacing Carbon Brushes Ridgid Recommends the Following AccessoriesLubrication SKU NoGeneral TroubleshootingTrouble Probable Cause Remedy Trouble Probable Cause Remedy MotorParts List for Ridgid 10 Inch Table Saw Model No. TS24001 Repair PartsKey Description Always Order by Part Number not by Key NumberRepair Parts Key Description 827483 Cover Blade Parts List for Ridgid 10 Inch Table Saw Model TS24001Always Order by Part Number Not by Key Number Description Miter Gauge AssemblyFence Assembly Guard Assembly Page Page Page Stock No. TS2400 Model No. TS24001 Serial No RIDGID, INC