RIDGID MS1065LZ manual Support Long Workpieces

Page 22

OPERATION

Align the cutting line on the workpiece with the edge of saw blade.

Grasp the stock firmly with one hand and secure it against the fence. Use the optional work clamp or a C-clamp to secure the workpiece when possible. See Figure 26.

WARNING:

To avoid serious personal injury, always keep your hands outside the no hands zone; at least 3 in. (7.6 cm) from blade. Never perform any cutting operation freehand (without holding workpiece against the fence). The blade could grab the workpiece if it slips or twists.

Before turning on the saw, perform a dry run of the cutting operation just to make sure that no problems will occur when the cut is made.

Grasp the saw handle firmly then squeeze the switch trigger. Allow several seconds for the blade to reach maximum speed.

Slowly lower the blade into and through the workpiece. See Figures 26 and 27.

Release the switch trigger and allow the saw blade to stop rotating before raising the blade out of workpiece. Wait until the electric brake stops blade from turning before removing the workpiece from miter table.

SUPPORT LONG WORKPIECES

See Figure 28.

Long workpieces need extra supports. Supports should be placed along the workpiece so it does not sag. The support should let the workpiece lay flat on the base of the saw and work table during the cutting operation. Use the optional work clamp or a C-clamp to secure the workpiece.

WARNING:

To avoid serious personal injury, always keep your hands outside the no hands zone; at least 3 in. (7.6 cm) from blade. Never perform any cutting operation freehand (without holding workpiece against the fence). The blade could grab the workpiece if it slips or twists.

45° X 45° COMPOUND MITER CUT

LONG WORKPIECE

WORKPIECE SUPPORTS

Fig. 27

Fig. 28

22

Image 22

Contents Operators Manual Table of Contents IntroductionRead ALL Instructions Safety and International SymbolsRules for Safe Operation ¥ Do not expose to rain or use in damp locationsBlade Coasts After Being Turned OFF Rules for Safe Operation Glossary of Terms for Woodworking Double Insulation SpecificationsElectrical Electrical ConnectionMm Combination Wrench UnpackingTools Needed Combination Square Framing SquareLoose Parts List AMP Motor FeaturesKnow Your Compound Miter SAW 10 IN. BladeMiter Lock Handle Blade Wrench / Storage AreaCarrying Handle Spindle Lock ButtonElectric Brake Positive Stops on Miter TableBevel Lock Knob Miter FenceDust BAG AssemblyDust Guide Work ClampTo Install Blade Table ExtensionSee Figures 13 AdjustmentsSquaring the SAW Blade to the Fence Socket Head Screws FenceMiter Miter Lock PlateBevel Lock Knob Miter Fence Blade Squaring the Blade to the Miter TableSee Figures 18 CombinationOperation Pivot Adjustments Travel Pivot AdjustmentBevel Pivot Adjustment ApplicationsTo Crosscut with Your Miter SAW Cutting with Your Compound Miter SAWCrosscutting Straight Crosscut Work ClampAT 45º Bevel CUTAT 48º Bevel CUTTo Make a Compound CUT with Your Miter SAW Compound Miter CUTCompound Miter CUT Work Clamp Support Long Workpieces 45 X 45 Compound Miter CUT Long Workpiece Workpiece SupportsCutting Compound Miters COMPOUND-ANGLE Settings for Popular StructuresPitch Side Cutting Crown Molding Laying Molding Flat on the Miter TableWrong Cutting Warped MaterialClamping Wide Workpieces RightAlignment Laser GuideOperation Blade Laser GuideChanging the Batteries Do not attempt to activate the laserGeneral MaintenanceLubrication What is Covered Under the Limited Three Year Warranty WarrantyDAY Satisfaction Guarantee Policy HOW to Obtain Service What is not CoveredCustomer Service Information Model No MS1065LZ Serial No