RIDGID MS1250LZA manual To Bevel Cut, See Figures 27, Bevel Scale, Indicator Point Screw

Page 24

OPERATION

TO Bevel Cut

See Figures 27 - 29.

A bevel cut is made by cutting across the grain of the workpiece with the blade angled to the workpiece. A straight bevel cut is made with the miter table set at the zero degree position and the blade set at an angle between -2°and 47°.

NOTE: It may be necessary to adjust the sliding miter fence to assure proper clearance prior to making the cut.

Pull out the lock pin and lift saw arm to its full height.

Loosen the miter lock handle. Rotate the miter lock han- dle approximately one-half turn to the left to loosen.

Press the miter lock plate down with your thumb and hold.

Rotate the miter table until the pointer aligns with zero on the miter scale.

Release the miter lock plate.

NOTE: You can quickly locate zero by releasing the lock plate as you rotate the control arm. The lock plate will seat itself in one of the built-in positive stop notches, located in the miter table frame.

Tighten the miter lock handle securely.

Loosen the bevel lock knob and move the saw arm to the left to the desired bevel angle.

Bevel angles can be set from -2°to 47°.

Once the saw arm has been set at the desired angle, securely tighten the bevel lock knob.

Place the workpiece flat on the miter table with one edge securely against the fence. If the board is warped, place the convex side against the fence. If the concave edge of a board is placed against the fence, the board could collapse on the blade at the end of the cut, jamming the blade. See Figures 34 - 35.

When cutting long pieces of lumber or molding, support the opposite end of the stock with a roller stand or with a work surface level with the saw table. See Figure 32.

Align the cutting line on the workpiece with the edge of saw blade.

Grasp the stock firmly with one hand and secure it against the fence. Use the work clamp or a C-clamp to secure the workpiece when possible. See Figure 30.

Before turning on the saw, perform a dry run of the cutting operation just to make sure that no problems will occur when the cut is made.

Grasp the saw handle firmly. Depress the switch lock with thumb then squeeze the switch trigger. Allow several seconds for the blade to reach maximum speed.

BEVEL

SCALE

scale

indicator

0

5 1

30 CM

45

INDICATOR

POINT

INDICATOR

SCREW

Fig. 27

Bevel Cut

®

WORK CLAMP

Fig. 28

 

BEVEL

STOP PIN

Fig. 29

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents OPERATOR’S Manual Table of Contents IntroductionGeneral Safety Rules Read all instructionsSpecific Safety Rules  Never Start a Tool When ANY ROTATiNG COMPonent is in Contact with the Workpiece Specific Safety Rules Symbols Symbol Name DESIGNATION/EXPLANATIONService Symbol Signal MeaningCord Length Wire Size A.W.G ElectricalDouble Insulation Electrical ConnectionGlossary of Terms Features Product SpecificationsSwitch Trigger Know Your Compound Miter SAWAMP Motor Miter Lock HandleTools Needed Loose Parts Dust GuideSocket Head Screws Dust BAGAssembly UnpackingMounting Holes Trace holes At these locations for hole patTernTable Extension Dust GuideExtension Washer Socket Head Washer Screw To install the work clamp Dust BAGWork Clamp Dust Bag QuickTo Install Blade BoltAligning the laser guide line Removing Your MarkTo Cut the Mark To Leave the MarkCutting a Slot In The Zero Clearance Throat Plate Squaring the SAW Blade to the FenceSee Figures 16 CAP Head ScrewsAdjustments are Required Sliding Miter Fence Adjustments are RequiredFence Miter Framing Table SquareSquaring the Blade to the Miter Table See Figures 22Lock Knob SquarePivot Adjustments Travel Pivot Adjustment Bevel Pivot AdjustmentOperation ApplicationsCutting with Your Compound Miter SAW To Cross cutStraight Cross cut Work clampIndicator Point Screw To Bevel CutSee Figures 27 Bevel ScaleTo Compound Miter Cut Compound Miter CutWork Clamp Support Long Workpieces See Figures 3045 x 45 Compound Miter CUT Long WorkpieceCOMPOUND-ANGLE Settings for Popular Structures Cutting Compound MitersPitch Side Cutting crown molding Laying molding flat on the miter tableLeft SIDE, Inside Corner Right SIDE, Outside Corner Right SIDE, Inside Corner Left SIDE, Outside CornerUsing a Crown Molding Support JIG Making a Crown Molding Support JIGCutting warped material See Figures 34Adjustments To Adjust the Laser GuideClamping wide workpieces Maintenance General MaintenanceBrush Replacement LubricationBattery Compartment Changing the Batteries in the laserBatteries Screw Laser GuideWarranty DAY Satisfaction Guarantee PolicyWhat is Covered Under the 3 Year Limited Service Warranty HOW to Obtain Service What is not CoveredCustomer Service Information Model NoMS1250LZA Serial No

MS1250LZA specifications

The RIDGID MS1250LZA is a versatile and robust miter saw designed for professionals and DIY enthusiasts alike. This powerful tool is engineered to deliver precision cutting for a wide range of materials, including wood, plastic, and light metals, making it an ideal choice for carpenters, contractors, and hobbyists.

One of the standout features of the MS1250LZA is its impressive 15-amp motor, which provides ample power to handle tough cutting tasks with ease. The motor is capable of reaching up to 5000 RPM, ensuring clean and accurate cuts every time. Whether you are making crosscuts, miters, or bevel cuts, this saw can handle it all with precision and efficiency.

The MS1250LZA incorporates a dual bevel design, allowing for both left and right angles of bevel cuts. This flexibility enhances the saw's usability, enabling users to create compound cuts without needing to flip the workpiece, which saves time and increases accuracy. The intuitive bevel adjustment lever allows for quick and straightforward adjustments, ensuring that you can easily switch between angles as needed.

Another significant technological advancement in the MS1250LZA is the laser guide system. This feature projects a clear, precise line on the cutting surface, providing enhanced visibility and accuracy. Users can easily line up their cuts without the guesswork, making it especially beneficial for intricate projects or when working with small pieces.

The saw's sliding feature is also noteworthy, as it allows for larger cuts with ease. The sliding arm can handle wider materials, making it perfect for framing lumber, larger boards, or even plywood sheets. Additionally, the positive stops on the miter table provide easy access to commonly used angles, streamlining the workflow for repetitive cuts.

Safety is paramount in any power tool, and the RIDGID MS1250LZA includes several safety features that protect both the user and the workpiece. The electric brake stops the blade quickly after the trigger is released, minimizing the risk of accidents. A transparent blade guard allows users to see the cutting area while keeping hands and fingers safe from the blade.

In terms of portability, the MS1250LZA is relatively lightweight and features a sturdy carrying handle, making it easy to transport between job sites. The durable construction ensures that it can withstand the rigors of professional use while delivering reliable performance over time.

Overall, the RIDGID MS1250LZA miter saw presents an impressive combination of power, flexibility, and safety features, making it an indispensable tool for any serious woodworking or construction project. With its user-friendly design and high-performance capabilities, it is sure to enhance the productivity and efficiency of its users.
Top Page Image Contents