RIDGID MS1250LZA manual Adjustments, Clamping wide workpieces, To Adjust the Laser Guide

Page 30

OPERATION

WRONG

Fig. 35

WARNING:

To avoid a kickback and to avoid serious personal injury, never position the concave edge of bowed or warped material against the fence.

clamping wide workpieces

See Figure 36.

When cutting wide workpieces, such as 2 in. x 6 in., boards should be clamped with a C-clamp as shown in figure 36.

WIDE BOARD

Fig. 36

 

ADJUSTMENTS

WARNING:

Before performing any adjustment, make sure the tool is unplugged from the power supply. Failure to heed this warning could result in serious personal injury.

TO ADJUST THE LASER GUIDE

See Figure 37.

NOTE: Avoid direct eye exposure when using the laser guide.

Set both the bevel angle and the miter table at 0°.

Use the work clamp or a C-clamp to secure a piece of scrap wood.

Plug the saw into the power source and make a slight cut to score the wood.

Raise the saw arm and unplug the saw.

Lift and hold the lower blade guard.

Rotate the blade by hand until you can push and hold the laser button and the laser is near the center of the workpiece as shown in figure 37.

To adjust the laser, turn the adjustment screw coun- ter-clockwise or clockwise using the hex key (1/16 in.) provided.

NOTE: When properly aligned, the laser should be on the left edge of the kerf.

Once aligned, remove and store the hex key (1/16 in.), and lower the blade guard.

NOTE: Always make practice cuts on scrap wood before cutting through your workpiece.

ADJUSTMENT

SCREW

HEX KEY

LASER

BUTTON APERTURE

LASER mark

Fig. 37

30

Page 29 Page 31
Image 30
Page 29 Page 31
Contents OPERATOR’S Manual Table of Contents IntroductionGeneral Safety Rules Read all instructionsSpecific Safety Rules  Never Start a Tool When ANY ROTATiNG COMPonent is in Contact with the Workpiece Specific Safety Rules Symbols Symbol Name DESIGNATION/EXPLANATIONService Symbol Signal MeaningDouble Insulation Cord Length Wire Size A.W.GElectrical Electrical ConnectionGlossary of Terms Features Product SpecificationsAMP Motor Switch TriggerKnow Your Compound Miter SAW Miter Lock HandleTools Needed Socket Head Screws Loose PartsDust Guide Dust BAGMounting Holes AssemblyUnpacking Trace holes At these locations for hole patTernTable Extension Dust GuideExtension Washer Socket Head Washer Screw Work Clamp To install the work clampDust BAG Dust Bag QuickTo Install Blade BoltTo Cut the Mark Aligning the laser guide lineRemoving Your Mark To Leave the MarkSee Figures 16 Cutting a Slot In The Zero Clearance Throat PlateSquaring the SAW Blade to the Fence CAP Head ScrewsFence Adjustments are Required Sliding Miter FenceAdjustments are Required Miter Framing Table SquareLock Knob Squaring the Blade to the Miter TableSee Figures 22 SquareOperation Pivot Adjustments Travel Pivot AdjustmentBevel Pivot Adjustment ApplicationsStraight Cutting with Your Compound Miter SAWTo Cross cut Cross cut Work clampSee Figures 27 Indicator Point ScrewTo Bevel Cut Bevel ScaleTo Compound Miter Cut Compound Miter CutWork Clamp 45 x 45 Compound Miter CUT Support Long WorkpiecesSee Figures 30 Long WorkpieceCOMPOUND-ANGLE Settings for Popular Structures Cutting Compound MitersPitch Side Left SIDE, Inside Corner Right SIDE, Outside Corner Cutting crown moldingLaying molding flat on the miter table Right SIDE, Inside Corner Left SIDE, Outside CornerCutting warped material Using a Crown Molding Support JIGMaking a Crown Molding Support JIG See Figures 34Adjustments To Adjust the Laser GuideClamping wide workpieces Brush Replacement MaintenanceGeneral Maintenance LubricationBatteries Battery CompartmentChanging the Batteries in the laser Screw Laser GuideWhat is Covered Under the 3 Year Limited Service Warranty WarrantyDAY Satisfaction Guarantee Policy HOW to Obtain Service What is not CoveredMS1250LZA Customer Service InformationModel No Serial No

MS1250LZA specifications

The RIDGID MS1250LZA is a versatile and robust miter saw designed for professionals and DIY enthusiasts alike. This powerful tool is engineered to deliver precision cutting for a wide range of materials, including wood, plastic, and light metals, making it an ideal choice for carpenters, contractors, and hobbyists.

One of the standout features of the MS1250LZA is its impressive 15-amp motor, which provides ample power to handle tough cutting tasks with ease. The motor is capable of reaching up to 5000 RPM, ensuring clean and accurate cuts every time. Whether you are making crosscuts, miters, or bevel cuts, this saw can handle it all with precision and efficiency.

The MS1250LZA incorporates a dual bevel design, allowing for both left and right angles of bevel cuts. This flexibility enhances the saw's usability, enabling users to create compound cuts without needing to flip the workpiece, which saves time and increases accuracy. The intuitive bevel adjustment lever allows for quick and straightforward adjustments, ensuring that you can easily switch between angles as needed.

Another significant technological advancement in the MS1250LZA is the laser guide system. This feature projects a clear, precise line on the cutting surface, providing enhanced visibility and accuracy. Users can easily line up their cuts without the guesswork, making it especially beneficial for intricate projects or when working with small pieces.

The saw's sliding feature is also noteworthy, as it allows for larger cuts with ease. The sliding arm can handle wider materials, making it perfect for framing lumber, larger boards, or even plywood sheets. Additionally, the positive stops on the miter table provide easy access to commonly used angles, streamlining the workflow for repetitive cuts.

Safety is paramount in any power tool, and the RIDGID MS1250LZA includes several safety features that protect both the user and the workpiece. The electric brake stops the blade quickly after the trigger is released, minimizing the risk of accidents. A transparent blade guard allows users to see the cutting area while keeping hands and fingers safe from the blade.

In terms of portability, the MS1250LZA is relatively lightweight and features a sturdy carrying handle, making it easy to transport between job sites. The durable construction ensures that it can withstand the rigors of professional use while delivering reliable performance over time.

Overall, the RIDGID MS1250LZA miter saw presents an impressive combination of power, flexibility, and safety features, making it an indispensable tool for any serious woodworking or construction project. With its user-friendly design and high-performance capabilities, it is sure to enhance the productivity and efficiency of its users.
Top Page Image Contents