RIDGID MS1250LZA manual Cutting with Your Compound Miter SAW, To Cross cut, Straight

Page 23

OPERATION

CUTTING WITH YOUR Compound MITER SAW

WARNING:

When using a work clamp or C-clamp to secure your workpiece, clamp workpiece on one side of the blade only. The workpiece must remain free on one side of the blade to prevent the blade from binding in workpiece. The workpiece binding the blade will cause motor stalling and kickback. This situation could cause an accident resulting in pos- sible serious personal injury.

WARNING:

To avoid serious personal injury, always tighten the miter lock handle securely before making a cut. Failure to do so could result in movement of the control arm or miter table while making a cut.

When cutting long pieces of lumber or molding, support the opposite end of the stock with a roller stand or with a work surface level with the saw table. See Figure 32.

Align cutting line on the workpiece with the edge of saw blade.

Grasp the stock firmly with one hand and secure it against the fence. Use the work clamp or a C-clamp to secure the workpiece when possible.

Before turning on the saw, perform a dry run of the cutting operation just to make sure that no problems will occur when the cut is made.

Grasp the saw handle firmly. Depress the switch lock with thumb then squeeze the switch trigger. Allow several seconds for the blade to reach maximum speed.

Slowly lower the blade into and through the workpiece.

Release the switch trigger and allow the saw blade to stop rotating before raising the blade out of workpiece. Wait until the electric brake stops blade from turning before removing the workpiece from the miter table.

To Cross cut

See Figure 26.

A cross cut is made by cutting across the grain of the workpiece. A straight cross cut is made with the miter table set at the 0° position. Miter cross cuts are made with the miter table set at some angle other than zero.

Pull out the lock pin and lift saw arm to its full height.

Loosen the miter lock handle. Rotate the miter lock handle approximately one-half turn to the left to loosen.

Press the miter lock plate down with your thumb and hold.

Rotate the miter table until the pointer aligns with the desired angle on the miter scale.

Release the miter lock plate.

NOTE: You can quickly locate 0°, 15°, 22.5°, 31.6°, and 45° left or right by releasing the lock plate as you rotate the control arm. The lock plate will seat itself in one of the positive stop notches, located in the miter table base.

Tighten the miter lock handle securely.

Place the workpiece flat on the miter table with one edge securely against the fence. If the board is warped, place the convex side against the fence. If the concave edge of a board is placed against the fence, the board could collapse on the blade at the end of the cut, jamming the blade. See Figures 34 - 35.

STRAIGHT

Cross cut

work clamp

Fig. 26

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents OPERATOR’S Manual Introduction Table of ContentsRead all instructions General Safety RulesPonent is in Contact with the Workpiece Specific Safety Rules Never Start a Tool When ANY ROTATiNG COM Specific Safety Rules Symbol Name DESIGNATION/EXPLANATION SymbolsSymbol Signal Meaning ServiceElectrical Connection Cord Length Wire Size A.W.GElectrical Double InsulationGlossary of Terms Product Specifications FeaturesMiter Lock Handle Switch TriggerKnow Your Compound Miter SAW AMP MotorTools Needed Dust BAG Loose PartsDust Guide Socket Head ScrewsTrace holes At these locations for hole patTern AssemblyUnpacking Mounting HolesExtension Washer Socket Head Washer Screw Table ExtensionDust Guide Dust Bag Quick To install the work clampDust BAG Work ClampBolt To Install BladeTo Leave the Mark Aligning the laser guide lineRemoving Your Mark To Cut the MarkCAP Head Screws Cutting a Slot In The Zero Clearance Throat PlateSquaring the SAW Blade to the Fence See Figures 16 Miter Framing Table Square Adjustments are Required Sliding Miter Fence Adjustments are Required FenceSquare Squaring the Blade to the Miter TableSee Figures 22 Lock KnobApplications Pivot Adjustments Travel Pivot AdjustmentBevel Pivot Adjustment OperationCross cut Work clamp Cutting with Your Compound Miter SAWTo Cross cut StraightBevel Scale Indicator Point ScrewTo Bevel Cut See Figures 27Work Clamp To Compound Miter CutCompound Miter Cut Long Workpiece Support Long WorkpiecesSee Figures 30 45 x 45 Compound Miter CUTPitch Side COMPOUND-ANGLE Settings for Popular StructuresCutting Compound Miters Right SIDE, Inside Corner Left SIDE, Outside Corner Cutting crown moldingLaying molding flat on the miter table Left SIDE, Inside Corner Right SIDE, Outside CornerSee Figures 34 Using a Crown Molding Support JIGMaking a Crown Molding Support JIG Cutting warped materialClamping wide workpieces AdjustmentsTo Adjust the Laser Guide Lubrication MaintenanceGeneral Maintenance Brush ReplacementScrew Laser Guide Battery CompartmentChanging the Batteries in the laser BatteriesHOW to Obtain Service What is not Covered WarrantyDAY Satisfaction Guarantee Policy What is Covered Under the 3 Year Limited Service WarrantySerial No Customer Service InformationModel No MS1250LZA
Top Page Image Contents