RIDGID MS1290LZ manual Maintenance and Lubrication, Maintenance Replacing Carbon Brushes

Page 42

Maintenance and Lubrication

Maintenance

DANGER: Never put lubricants on the blade while it is spinning.

WARNING: To reduce the risk of injury from unexpected starting or electrical shock, unplug the power cord before working on the saw.

WARNING: For your safety, this saw i s d ou bl e in su la te d . To avoid electrical shock, fire or injury, use only parts identical to those identified in the parts list. Reassemble exactly as original assembly to avoid electrical shock.

Replacing Carbon Brushes

The carbon brushes furnished will last approximately 50 hours of running time or 10,000 on/off cycles. Replace both carbon brushes when either has less than 1/4" length of carbon remaining. To inspect or replace brushes, first unplug the saw. Then remove the black plastic cap on the side of the motor (caution, this cap is spring loaded by the brush assembly). Then pull out the brush. Repeat for the other side. To reassemble reverse the procedure. The ears on the metal end of the brush assem- bly go in the same hole the carbon part fits into. Tighten the cap snugly but do not overtighten.

NOTE: To reinstall the same brushes, first make sure the brushes go back in the way they came out. Otherwise a break-in period will occur that will reduce motor performance and increase brush wear.

Lower Blade Guard

Do not use the saw without the lower guard. The lower blade guard is attached to the saw for your protection. Should the lower guard become damaged, do not use the saw until damaged guard has been replaced. Develop a regular check to make sure the lower guard is working properly. Clean the lower guard of any dust or build up with a damp cloth.

CAUTION: Do not use solvents on the guard. They could make the plastic "cloudy" and brittle.

WARNING: When cleaning lower guard unplug the saw from the out- let to avoid unexpected start-up.

Periodically, sawdust will accumulate under the work table and base. This could cause difficulty in the movement of the work table when setting up a miter cut. Frequently blow out or vacuum up the sawdust.

WARNING: If blowing sawdust, wear proper eye protection to keep debris from blowing into eyes.

42

Image 42

Contents Page Table of Contents Safety Instructions For Miter Saw Safety Signal Words Before Using The SawSafety Instructions for Miter Saws When Installing Or Moving The Miter SawBefore Each Use Plan Ahead To Protect Your Eyes, Hands, Face and Ears Keep Guards In Place, in workingTo Reduce the Risk of Accidental Dress For Safety Preparing to Make CutWhenever Saw Is Running Don’t Overreach. Keep good foot- ing and balanceGlossary of Terms for Woodworking Before Leaving The SawMotor Specifications and Electrical Requirements Extension Cord Wire Sizes Length Motor Safety ProtectionWire Sizes Polarized PlugUnpacking and Checking Contents Getting to Know Your Miter Saw Saw at a desired bevel angleTop Carrying Handle Convenient way to transport saw Stop Screw Arbor AssemblyInstalling or Removing the Blade Fit 1/4 hex end of combination toolBe sure the arbor lock is released so the blade turns freely Workpiece Clamp Installation Four Basic Saw ControlsAssembling Dust Bag Bevel Lock Lever Bevel Index Pin Depth Adjustment Cam Knob Step One Repositioning Zero Clear- ance Blade Insert Alignment AdjustmentsStep Two Slide Tube Adjustment Loosen the top two gib screwsAdjust Miter Scale Indicator Step Three Blade Square to Fence Miter AlignmentStep Four Blade Square to Table Bevel Adjustment Adjust Bevel Scale IndicatorMiter Lock Lever Adjustment To check, follow these stepsMiter Lock Lever Loosen the top locking jam nut Bevel Lock Lever AdjustmentBevel Pivot Movement/Adjustment Nut LockPortable Applications Mounting The Miter SawGrip of the plastic handle. Car Work Bench ApplicationsSafety Instructions for Basic Saw Operations Check Damaged Parts. Check forSafety Instructions for Basic Saw Operations con’t Reduce the Risk of AccidentalPreparing to Make the Cut Inspect Your Workpiece. Make sureMake workshop child-proof. Install Basic Saw Operations Chop Cutting Body and Hand PositionSliding Fence Miter CutBevel Cut Miter Scale UsageCutting Compound Miters on Picture Frames and Boxes Cutting Bowed MaterialCompound Cut Compound Cut BoxWork against the blade Completely set up your sawWorkpieces. Avoid binding Workpiece Clamp Usage Always perform dry runs. MakeWorkpiece Support Auxiliary FenceCut the two outside grooves Rough Cutting a DadoCutting Base Moldings Cut These Grooves With Saw Use a Chisel toCutting Crown Moldings Two Methods of Cutting Crown MoldingCutting Crown Molding Flat on the Miter Saw Table Cutting Crown Molding Angled to the Table and Fence Making a crown molding support jigWall Wall to Crown Molding Angle 45 degrees Laser System Mounting the Laser SystemCoverplate Stop Screw Arbor Blade Arbor Lock Supplied with Inner Blade Left Hand Thread Supplied withExactline Spindle Keep these items for use if Laser system is removedOperation Broken Red LineChanging Batteries Replace the back cover and secure with two Phillips screwsMaintenance and Lubrication Maintenance Replacing Carbon BrushesLower Blade Guard Ball Bearings LubricationMotor Belt Tension Infrequent Lubrication as RequiredRecommended Accessories AccessoriesUsing Carbide Tipped Blades Prohibited AccessoriesTroubleshooting Guide Problem Probable Cause Suggested Corrective ActionGeneral Wiring Diagram Trouble Shooting of Brake by Qualified Service Person OnlyMotor Page Repair Parts ‡ Caution See mechanical assembly caution on Always order by part number not by key numberStandard Hardware Item May be purchased locally Base/Table Assembly Table Assembly Base Assembly Pivot Assembly Tube Pivot Assembly Pivot Sub Assembly Arm Guard Assembly ‡ Lower Guard Assembly ‡ Motor Assembly Page Catalog No. MS1290LZ Model No. MS1290LZ0Serial No RIDGID,INCPart No. SP6505 Form No. SP6505