RIDGID MS1290LZ manual Pivot Sub Assembly

Page 55

Repair Parts

Parts List For RIDGID 12" Compound Miter Saw

Model No. MS1290LZ 0

RIDGID parts are available on-line at www.ridgidparts.com

Figure 7 - Pivot Sub Assembly

8

7

6
5	1
	1

4

2

3

Always order by Part Number - Not by Key Number

	Key	Part No.	Description
	No.	Part No.	Description
	No.


	1	—	Pivot Asm. (See Fig. 5)
	2	830151	Screw, Shoulder M6
	3	830010	Clamp, Bevel
	4	830011	Screw, Shoulder
			M8 x 1.25 x 58.5
	5	821063-7	* Washer, 8 x 16 x 1.2
	6	820236-7	* Nut, Hex M8 x 1.25
	7	830012	Plunger, Bevel Lock
	8	830013	Lever, Bevel Lock

* Standard hardware item - May be purchased locally.

55

Image 55

Contents Page Table of Contents Safety Signal Words Before Using The Saw Safety Instructions For Miter SawWhen Installing Or Moving The Miter Saw Safety Instructions for Miter SawsBefore Each Use Keep Guards In Place, in working Plan Ahead To Protect Your Eyes, Hands, Face and EarsTo Reduce the Risk of Accidental Preparing to Make Cut Dress For SafetyDon’t Overreach. Keep good foot- ing and balance Whenever Saw Is RunningBefore Leaving The Saw Glossary of Terms for WoodworkingMotor Specifications and Electrical Requirements Polarized Plug Motor Safety ProtectionWire Sizes Extension Cord Wire Sizes LengthUnpacking and Checking Contents Saw at a desired bevel angle Getting to Know Your Miter SawTop Carrying Handle Convenient way to transport saw Fit 1/4 hex end of combination tool AssemblyInstalling or Removing the Blade Stop Screw ArborBe sure the arbor lock is released so the blade turns freely Four Basic Saw Controls Workpiece Clamp InstallationAssembling Dust Bag Bevel Lock Lever Bevel Index Pin Depth Adjustment Cam Knob Loosen the top two gib screws Alignment AdjustmentsStep Two Slide Tube Adjustment Step One Repositioning Zero Clear- ance Blade InsertStep Three Blade Square to Fence Miter Alignment Adjust Miter Scale IndicatorAdjust Bevel Scale Indicator Step Four Blade Square to Table Bevel AdjustmentTo check, follow these steps Miter Lock Lever AdjustmentMiter Lock Lever Nut Lock Bevel Lock Lever AdjustmentBevel Pivot Movement/Adjustment Loosen the top locking jam nutWork Bench Applications Mounting The Miter SawGrip of the plastic handle. Car Portable ApplicationsCheck Damaged Parts. Check for Safety Instructions for Basic Saw OperationsReduce the Risk of Accidental Safety Instructions for Basic Saw Operations con’tInspect Your Workpiece. Make sure Preparing to Make the CutMake workshop child-proof. Install Basic Saw Operations Body and Hand Position Chop CuttingMiter Scale Usage Miter CutBevel Cut Sliding FenceCompound Cut Box Cutting Bowed MaterialCompound Cut Cutting Compound Miters on Picture Frames and BoxesWorkpiece Clamp Usage Always perform dry runs. Make Completely set up your sawWorkpieces. Avoid binding Work against the bladeAuxiliary Fence Workpiece SupportCut These Grooves With Saw Use a Chisel to Rough Cutting a DadoCutting Base Moldings Cut the two outside groovesTwo Methods of Cutting Crown Molding Cutting Crown MoldingsCutting Crown Molding Flat on the Miter Saw Table Making a crown molding support jig Cutting Crown Molding Angled to the Table and FenceWall Wall to Crown Molding Angle 45 degrees Mounting the Laser System Laser SystemCoverplate Stop Screw Arbor Blade Arbor Lock Spindle Keep these items for use if Laser system is removed Left Hand Thread Supplied withExactline Supplied with Inner BladeBroken Red Line OperationReplace the back cover and secure with two Phillips screws Changing BatteriesMaintenance Replacing Carbon Brushes Maintenance and LubricationLower Blade Guard Infrequent Lubrication as Required LubricationMotor Belt Tension Ball BearingsProhibited Accessories AccessoriesUsing Carbide Tipped Blades Recommended AccessoriesProblem Probable Cause Suggested Corrective Action Troubleshooting GuideGeneral Trouble Shooting of Brake by Qualified Service Person Only Wiring DiagramMotor Page Repair Parts Always order by part number not by key number ‡ Caution See mechanical assembly caution onStandard Hardware Item May be purchased locally Base/Table Assembly Table Assembly Base Assembly Pivot Assembly Tube Pivot Assembly Pivot Sub Assembly Arm Guard Assembly ‡ Lower Guard Assembly ‡ Motor Assembly Page Form No. SP6505 RIDGID,INCPart No. SP6505 Catalog No. MS1290LZ Model No. MS1290LZ0Serial No