Emerson CF710AB00, CF711PBOO owner manual For Standard Mounting For Close-to-the-Ceiling Mounting

Page 4

IMPORTANT

Your ceiling fan is designed to be installed either in the standard manner, or in the close-to-the-ceiling manner. Using the standard method, the hanger ball/downrod assembly will suspend the fan several inches below the ceiling cover. Using the close-to-the-ceiling method, the ceiling cover installs directly on the fan motor housing, thus mounting the fan 3-1/2 inches closer to the ceiling than the standard method. In no

DECORATIVE

CAP

HAIRPIN

CLIP

MOTOR COUPLING

HANGER BALL/DOWNROD ASSEMBLY

CEILING

COVER

SETSCREW

CLEVIS

PIN

case should the fan blades be lower than seven feet above the floor. Depending on your desired mounting method, proceed to

“INSTALLING HANGER BALL/DOWNROD ASSEMBLY” for standard mounting, or to

“INSTALLING CEILING COVER ON FAN MOTOR HOUSING” for close-to-the-ceiling mounting.

SETSCREW

Figure 1

Installing The Hanger

Installing The Ceiling Cover

Ball/Downrod Assembly

On The Fan Motor Housing

(For Standard Mounting)

(For Close-to-the-Ceiling Mounting)

1.Pass the 56" motor leads through the opening in the ceiling cover. Be sure the cover is oriented correctly.

2. Separate, untwist and unkink the three motor leads. Route the motor leads through the hanger ball/downrod assembly.

3.Loosen the two setscrews in the motor coupling. Align the clevis pin holes in the downrod with the holes in the motor coupling. Install the clevis pin and secure with the hairpin clip (Figure 1). The clevis pin must go through the holes in the motor coupling and the holes in the downrod. Be sure to push the straight leg of the hairpin clip through the hole near the end of the clevis pin until the curved portion of the hairpin clip snaps around the clevis pin. The hairpin clip must be properly installed to prevent the clevis pin from working loose. Pull on the hanger ball to make sure the clevis pin is properly installed.

! WARNING

It is critical that the clevis pin in the motor coupling is properly installed and the setscrews securely tightened. Failure to verify that the pin and setscrews are properly installed could result in the fan falling.

1.Remove and retain three screws from the top of the motor housing (Figure 2A).

2.Position the rubber gasket (supplied in parts bag) on the motor housing (small holes in gasket centered over the screw holes in the housing) (Figure 2B).

REMOVE SCREWS (3)

INSTALL GASKET

Figure 2A

Figure 2B

3.Gently pry the decorative cap (Figure 1) from the ceiling cover. Align the holes in the ceiling cover with the holes in the motor housing and secure using the three screws (Figure 3).

4.While pulling up on the hanger ball, securely tighten the two setscrews in the motor coupling (Figure 1).

NOTE: The setscrews must be properly installed as described above, or fan wobble could result.

5.The fan comes with blue, black and white leads that are 56” long. Measure up approximately 6 to 9-inches above top of hanger ball/downrod assembly. Cut off excess leads and strip back insulation 1/2-inch from end of leads.

4

RUBBER

SCREW (3)

GASKET

 

Figure 3

4.The fan comes with blue, black and white leads that are 56” long. Measure up approximately 6 to 9-inches above the motor coupling. Cut off excess leads and strip back insulation 1/2-inch from ends of leads.

Image 4
Contents Read and Save These Instructions Safety Instructions Additional Safety Instructions for InstallationTools Needed for Assembly MaterialsFor Standard Mounting For Close-to-the-Ceiling Mounting Standard Method Using Hanger Ball/Downrod Installing Hanger BracketHanging The Ceiling Fan Wiring The Ceiling Fan Electrical RequirementsInstalling The Fan Blades Installing Ceiling CoverInstalling The Glass Shades Removal Light FixtureUsing Your Ceiling Fan Trouble ShootingMaintenance AccessoriesRepair Parts HOW to Order Repair PartsRepair Parts Listing CF710PB00 CF710BS00