Quantum 1400, 1420, 1470 O M F O R T a D J U S T M E N T S, Seat Height and Seat Angle Adjustment

Page 20

V . C O M F O R T A D J U S T M E N T S

COMFORT ADJUSTMENTS

After becoming familiar with your power chair’s operation, you may find the need to make some adjustments to increase your comfort, such as seat height and angle, armrest angle, footrest height and angle, and the controller’s position. If your power chair is equipped with a Synergy Seat or the TRU-Balance, refer to the information provided in separate manuals. If your power chair is equipped with a medium back, a high back, or a reclining seat, refer to the following information.

WARNING! If your power chair was configured at your authorized Pride provider, please consult your healthcare professional before changing the seat position or making any other adjustment. Some adjustments may degrade your power chair’s performance and safety by changing its center of gravity.

You may need the following to make comfort adjustments:

νmetric/standard hex key set

νmetric/standard socket set and ratchet

νadjustable wrench

Seat Height and Seat Angle Adjustment

There are four seat towers that connect the seat to the power base. See figures 3 and 8. You can change the seat height to one of three positions in 1-in. increments by raising the seat towers. If you raise or lower only one set of seat towers (front or rear), you can also change the seat base angle. If your power chair is equipped with a power elevating seat, then you change the seat height through the controller or a switch.

To change the seat height or seat angle:

1.Unplug the connector(s) from the electronics tray.

2.Press both seat plungers and lift up the front of the seat (if equipped withfootrest).See figure 7.Pressbothfrontseat towerlatchesandliftup thefrontoftheseat(elevatinglegrestsandswing-awayfootrest).Seefigure 8.

3.Allow the seat to rest on the front seat towers.

4.Pulltheseatforwardandliftitofftheframe.

WARNING! Do not pick up the seat by the armrests. They are free to pivot, and you may lose control of the seat if they do so, resulting in personal injury and/or damage to the chair.

5.Lift off the shroud.

6.Remove the ball detent pin from each of the four seat towers. See figure 8.

7.Raise or lower each seat tower to the desired position. To change the angle, set either the front or rear seat towers higher or lower than the other.

8.Reinstall the ball detent pin into each seat tower.

9.Reinstall the shroud.

10.Reinstalltheseat.

11.Plugtheconnectorsintotheelectronicstray.

SEAT PLUNGERS

Figure 7. Seat Plungers

REAR SEAT TOWER

FRONT SEAT TOWER

FRONT SEAT TOWER LATCH

BALL

DETENT

PINS

Figure 8. Front and Rear Seat Towers

22

www.pridemobility.com

Quantum Jazzy 1400 Series Rev C Feb 04

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Includes 1470, 1420, F E T Y G U I D E L I N E S Copyright PrideMobilityProductsCorpN T E N T S N T R O D U C T I O N IntroductionInformationExchange PrideMobilityProductsCorporation AttnCustomerCareDepartmentPride Owners Club MyAuthorized Pride ProviderIsModifications Pre-Ride Safety CheckS a F E T Y Incline Information Weight LimitationsTire Inflation Outdoor Driving Surfaces Braking InformationCornering Information Public Streets and Roadways Stairs and Escalators Freewheel ModeStationary Obstacles Steps, Curbs, etc EMI & RFI Batteries Inclement Weather Precautions Reaching and BendingPositioning Belts Alcohol Removable PartsFrequently Asked Questions FAQs Where do radio waves come from?Are all power chairs susceptible to EMI/RFI? I . E M I / R FWhat is the FDA doing about the problem? What should I do if my power chair moves unexpectedly?T H E Q UA N T U M JA Z Z Y 1 4 0 0 S E R I E S Quantum Jazzy 1470 1420 and 1400 are similarSpecifications Battery Electronics Tray Active-Trac SuspensionTo operate the manual freewheel lever Manual Freewheel LeverTo operate the manual freewheel lever 1400 Seat Height and Seat Angle Adjustment Unplug the connectors from the electronics trayO M F O R T a D J U S T M E N T S To change the seat height or seat angleTo adjust the seatback angle Seatback Angle AdjustmentArmrest WidthAdjustment ArmrestAngleAdjustment To change the armrest angleTo adjust the footrest angle Footrest AngleController Position To extend the controllerTo adjust the SFR length To adjust the ELR angleTo adjust the ELR length Swing-away FootrestsTo adjust the anti-tip wheels Anti-Tip WheelsPower Elevating Seat Option Power Elevating Seat ActuatorTo use the swivel feature Power Elevating Seat OperationTo operate the power elevating seat To charge the batteries using the onboard charger To charge the batteries using the off-board chargerB a T T E R I E S a N D C H a R G I N G Batteries and ChargingFrequently Asked Questions FAQs How does the charger work? Can I use a different battery charger?How often must I charge the batteries? Daily UseUse these specifications to reorder deep-cycle batteries Why do my new batteries seem weak?How can I get maximum range or distance per charge? What type of batteries should I use?How can I ensure maximum battery life? How should I store my Power Chair and its batteries?What about public transportation? What about shipping?Page I . O P E R a T I O N Speed Settings To select a speed settingPower Accessories Power ModuleTrouble Codes Sleep ModeActuator Lighting Module Not Shown Motor wiring harnesses Battery wiring harnesses Other components are located inside the power baseEuropa Master Remote JoystickOn/off key toggles the system power on and off To enable the lockout systemOn/Off Key System Status LightTo change the drive mode program Drive Mode and Actuator Display also Remote Status DisplayBattery Saver Feature Sleep Mode If EnabledFault Codes Flash Code Sequence Diagnosis SolutionCare and Maintenance Should your power chair come in contact with waterTemperature I I . C a R E a N D M a I N T E N a N C EDaily Checks Weekly ChecksTo check the brakes To calibrate the joystick Remote Plus onlyCleaning Precautions Tire/Wheel Replacement Monthly ChecksYearly Checks StorageBattery Replacement To replace the batteriesTo inspect or replace the motor brushes Corrective MaintenanceMotor Brushes Optional Accessories O P T I O N a L a C C E S S O R I E SLifetime Limited Warranty A R R a N T YT E S Europa Controller Remote Plus ControllerFit and Finish Performance Inclusion of all Parts
Related manuals
Manual 2 pages 44.46 Kb Manual 2 pages 57.43 Kb

1470, 1400, 1420 specifications

The Quantum 6000 XL, 1650, and 1420 are advanced models designed for high-performance applications, showcasing cutting-edge technologies and remarkable features. These machines are engineered to meet the demands of various industries, providing efficiency and precision in their operations.

Starting with the Quantum 6000 XL, this model stands out due to its enhanced processing capabilities, allowing it to handle complex tasks with ease. It is equipped with a high-speed processor and a robust memory architecture, enabling seamless multitasking and processing of large data sets. The XL version features a larger work area, making it ideal for projects that require extensive space and resources. Its advanced cooling system ensures optimal performance during prolonged use, minimizing thermal throttling and maximizing productivity.

The Quantum 1650 model is designed for versatility, offering a balance between performance and resource management. It incorporates energy-efficient technologies that lower operational costs without compromising output quality. With its intuitive user interface, operators can easily navigate through features and settings, enhancing workflow and reducing the learning curve. The 1650 is also equipped with modular components that can be upgraded or replaced, ensuring longevity and adaptability to future technological advancements.

Meanwhile, the Quantum 1420 model is tailored for compact environments where space is a premium. Despite its smaller footprint, it boasts powerful functionalities that rival larger machines. Features such as precision sensors and advanced software algorithms allow for accurate performance monitoring, ensuring that results consistently meet high standards. The 1420 is optimized for quick setup and teardown, making it a favorite for jobs that require agility and speed.

Common to all three models is their commitment to connectivity and integration. Equipped with multiple communication interfaces, they can seamlessly connect with various devices and networks, allowing for real-time data transfer and remote monitoring. Moreover, their compatibility with industry-standard software enhances their usability across different platforms.

In conclusion, the Quantum 6000 XL, 1650, and 1420 represent the forefront of technological innovation, each tailored to specific needs while sharing a foundation of robust performance, efficiency, and connectivity. These models are tailored for industries looking to leverage advanced machinery to boost productivity and operational efficiency.
Top Page Image Contents