Quantum 1470, 1420, 1400 manual Power Elevating Seat Option, Power Elevating Seat Actuator

Page 25

V . C O M F O R T A D J U S T M E N T S

Power Elevating Seat Option

Your power chair may be equipped with a power elevating seat actuator. See figure 18.The power elevating seat is equipped with a system that reduces the power chair’s speed by one half whenever the seat is elevated more than 1-2 inches.

The power elevating seat can enhance the capabilities of the power chair in several ways:

νBy elevating the seat, your level of reach is extended to allow more freedom and independence in many environments.

νYou can easily adjust the power chair’s seat height to any surface to which you want to transfer.The seat swivels 90 degrees to whichever side the joystick is located.

νBy raising your seat, you are closer to the eye level of standing persons. This provides better interaction.

For all the benefits your elevating seat can provide you, there are limitations. Observe the following precautions in order to ensure safe use of the power chair Elevating Seat option.

νRead and understand this owner’s manual thoroughly before operating the power chair.

νAlways fasten the positioning belt (if so equipped) when operating the elevating seat.

νOperate the power chair only on a flat level surface whenever the elevating seat is raised from its lowest position.

WARNING! The power elevating seat option is intended for use on a level surface only. Never raise the seat from its lowest position on an inclined surface. Failure to heed this warning can result in the power chair tipping over and causing injury.

WARNING! Never raise the seat from its lowest position when operating your power chair on bumpy or uneven surfaces. Failure to heed this warning can result in the power chair tipping over and causing injury.

WARNING! Never raise the power elevating seat while your power chair is in the freewheel mode.

WARNING! Always fasten the positioning belt when operating the power elevating seat. The power elevating seat option is equipped with a system that reduces your Jazzy’s speed by one half when the seat is elevated more than 1 - 2 inches. Always check to be sure this system is operating properly before using your Jazzy.

Figure 18. Power Elevating Seat Actuator

Quantum Jazzy 1400 Series Rev C Feb 04

www.pridemobility.com

27

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Includes 1470, 1420, Copyright PrideMobilityProductsCorp F E T Y G U I D E L I N E SN T E N T S Introduction N T R O D U C T I O NInformationExchange PrideMobilityProductsCorporation AttnCustomerCareDepartmentMyAuthorized Pride ProviderIs Pride Owners ClubS a F E T Y Pre-Ride Safety CheckModifications Tire Inflation Weight LimitationsIncline Information Cornering Information Braking InformationOutdoor Driving Surfaces Stationary Obstacles Steps, Curbs, etc Freewheel ModePublic Streets and Roadways Stairs and Escalators EMI & RFI Positioning Belts Inclement Weather Precautions Reaching and BendingBatteries Removable Parts AlcoholWhere do radio waves come from? Frequently Asked Questions FAQsAre all power chairs susceptible to EMI/RFI? I . E M I / R FWhat should I do if my power chair moves unexpectedly? What is the FDA doing about the problem?Quantum Jazzy 1470 1420 and 1400 are similar T H E Q UA N T U M JA Z Z Y 1 4 0 0 S E R I E SSpecifications Battery Active-Trac Suspension Electronics TrayTo operate the manual freewheel lever 1400 Manual Freewheel LeverTo operate the manual freewheel lever Unplug the connectors from the electronics tray Seat Height and Seat Angle AdjustmentO M F O R T a D J U S T M E N T S To change the seat height or seat angleSeatback Angle Adjustment To adjust the seatback angleArmrest WidthAdjustment ArmrestAngleAdjustment To change the armrest angleFootrest Angle To adjust the footrest angleController Position To extend the controllerTo adjust the ELR angle To adjust the SFR lengthTo adjust the ELR length Swing-away FootrestsAnti-Tip Wheels To adjust the anti-tip wheelsPower Elevating Seat Actuator Power Elevating Seat OptionTo operate the power elevating seat Power Elevating Seat OperationTo use the swivel feature To charge the batteries using the off-board charger To charge the batteries using the onboard chargerB a T T E R I E S a N D C H a R G I N G Batteries and ChargingCan I use a different battery charger? Frequently Asked Questions FAQs How does the charger work?How often must I charge the batteries? Daily UseWhy do my new batteries seem weak? Use these specifications to reorder deep-cycle batteriesHow can I get maximum range or distance per charge? What type of batteries should I use?How should I store my Power Chair and its batteries? How can I ensure maximum battery life?What about public transportation? What about shipping?Page I . O P E R a T I O N To select a speed setting Speed SettingsPower Accessories Power ModuleActuator Lighting Module Not Shown Sleep ModeTrouble Codes Other components are located inside the power base Motor wiring harnesses Battery wiring harnessesEuropa Master Remote JoystickTo enable the lockout system On/off key toggles the system power on and offOn/Off Key System Status LightDrive Mode and Actuator Display also Remote Status Display To change the drive mode programBattery Saver Feature Sleep Mode If EnabledFlash Code Sequence Diagnosis Solution Fault CodesShould your power chair come in contact with water Care and MaintenanceTemperature I I . C a R E a N D M a I N T E N a N C EWeekly Checks Daily ChecksTo check the brakes To calibrate the joystick Remote Plus onlyMonthly Checks Cleaning Precautions Tire/Wheel ReplacementYearly Checks StorageTo replace the batteries Battery ReplacementMotor Brushes Corrective MaintenanceTo inspect or replace the motor brushes O P T I O N a L a C C E S S O R I E S Optional AccessoriesA R R a N T Y Lifetime Limited WarrantyT E S Remote Plus Controller Europa ControllerFit and Finish Performance Inclusion of all Parts
Related manuals
Manual 2 pages 44.46 Kb Manual 2 pages 57.43 Kb

1470, 1400, 1420 specifications

The Quantum 6000 XL, 1650, and 1420 are advanced models designed for high-performance applications, showcasing cutting-edge technologies and remarkable features. These machines are engineered to meet the demands of various industries, providing efficiency and precision in their operations.

Starting with the Quantum 6000 XL, this model stands out due to its enhanced processing capabilities, allowing it to handle complex tasks with ease. It is equipped with a high-speed processor and a robust memory architecture, enabling seamless multitasking and processing of large data sets. The XL version features a larger work area, making it ideal for projects that require extensive space and resources. Its advanced cooling system ensures optimal performance during prolonged use, minimizing thermal throttling and maximizing productivity.

The Quantum 1650 model is designed for versatility, offering a balance between performance and resource management. It incorporates energy-efficient technologies that lower operational costs without compromising output quality. With its intuitive user interface, operators can easily navigate through features and settings, enhancing workflow and reducing the learning curve. The 1650 is also equipped with modular components that can be upgraded or replaced, ensuring longevity and adaptability to future technological advancements.

Meanwhile, the Quantum 1420 model is tailored for compact environments where space is a premium. Despite its smaller footprint, it boasts powerful functionalities that rival larger machines. Features such as precision sensors and advanced software algorithms allow for accurate performance monitoring, ensuring that results consistently meet high standards. The 1420 is optimized for quick setup and teardown, making it a favorite for jobs that require agility and speed.

Common to all three models is their commitment to connectivity and integration. Equipped with multiple communication interfaces, they can seamlessly connect with various devices and networks, allowing for real-time data transfer and remote monitoring. Moreover, their compatibility with industry-standard software enhances their usability across different platforms.

In conclusion, the Quantum 6000 XL, 1650, and 1420 represent the forefront of technological innovation, each tailored to specific needs while sharing a foundation of robust performance, efficiency, and connectivity. These models are tailored for industries looking to leverage advanced machinery to boost productivity and operational efficiency.
Top Page Image Contents