Quantum 1420, 1470, 1400 Reclining Seat, To adjust the seatback angle, Seatback Angle Adjustment

Page 21

V . C O M F O R T A D J U S T M E N T S

Reclining Seat

If your power chair is equipped with a reclining seat, you can adjust the seatbackanglewiththeseatbackreleaselever.Theleverislocatedontheright side of the seat base.

To adjust the seatback angle:

1.Press down on the lever.

2.Move the seatback to the desired position.

3.Release the lever.

Seatback Angle Adjustment

If your power chair is equipped with an adjustable seatback, you can adjust it to four different angles: 90°, 102°, 105°, or 107°.

To adjust the seatback angle:

1.Remove the adjusting screws on both seat hinges. See figure 9.

2.Set the seatback at desired angle.

3.Reinstallthescrewsonbothseathingesandtighten.

Armrest WidthAdjustment

Youcanchangeeacharmrest’s width independently of each other.

NOTE: Changing the armrest width may increase the overall width of your power chair.

ADJUSTING

SCREW

ARMRESTKNOB

JAM NUT JAM NUT

To change the armrest width:

1.Locate the two armrest knobs on each side of the armrest receiver bracket. See figure 9.

2.Loosen the knobs.

3.Slide the armrests in or out to the desired width.

4.Tightenthearmrestknobs.

Figure 9. Seatback and Armrest Adjustments

ArmrestAngleAdjustment

To change the armrest angle:

1.Liftthearmreststraightupsothatitisperpendiculartothefloor.

2.Loosen the jam nuts. See figure 9.

3.Loosen the adjusting screw. See figure 9.

4.Turntheadjustingscrewclockwisetoraisethefrontofthearmrest,orturntheadjustingscrewcounterclockwisetolowerthefront ofthearmrest.

5.Tightenthejamnutstolocktheadjustingscrewintoplace.

Footrest Height

Thefootrestheightiseasilyadjustedtosixdifferentheights.

To raise or lower the footrest:

1.Use a hex key to remove the bolt, spacers, and nut from the footrest. See figure 10.

2.Raiseorlowerthefootresttothedesiredheight.

3.Reinstallthebolt,spacers,andnutintothefootrest.

Quantum Jazzy 1400 Series Rev C Feb 04

www.pridemobility.com

23

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Includes 1470, 1420, Copyright PrideMobilityProductsCorp F E T Y G U I D E L I N E SN T E N T S Introduction N T R O D U C T I O NInformationExchange PrideMobilityProductsCorporation AttnCustomerCareDepartmentMyAuthorized Pride ProviderIs Pride Owners ClubPre-Ride Safety Check S a F E T YModifications Weight Limitations Tire InflationIncline Information Braking Information Cornering InformationOutdoor Driving Surfaces Freewheel Mode Stationary Obstacles Steps, Curbs, etcPublic Streets and Roadways Stairs and Escalators EMI & RFI Inclement Weather Precautions Reaching and Bending Positioning BeltsBatteries Removable Parts AlcoholWhere do radio waves come from? Frequently Asked Questions FAQsAre all power chairs susceptible to EMI/RFI? I . E M I / R FWhat should I do if my power chair moves unexpectedly? What is the FDA doing about the problem?Quantum Jazzy 1470 1420 and 1400 are similar T H E Q UA N T U M JA Z Z Y 1 4 0 0 S E R I E SSpecifications Battery Active-Trac Suspension Electronics TrayManual Freewheel Lever To operate the manual freewheel lever 1400To operate the manual freewheel lever Unplug the connectors from the electronics tray Seat Height and Seat Angle AdjustmentO M F O R T a D J U S T M E N T S To change the seat height or seat angleSeatback Angle Adjustment To adjust the seatback angleArmrest WidthAdjustment ArmrestAngleAdjustment To change the armrest angleFootrest Angle To adjust the footrest angleController Position To extend the controllerTo adjust the ELR angle To adjust the SFR lengthTo adjust the ELR length Swing-away FootrestsAnti-Tip Wheels To adjust the anti-tip wheelsPower Elevating Seat Actuator Power Elevating Seat OptionPower Elevating Seat Operation To operate the power elevating seatTo use the swivel feature To charge the batteries using the off-board charger To charge the batteries using the onboard chargerB a T T E R I E S a N D C H a R G I N G Batteries and ChargingCan I use a different battery charger? Frequently Asked Questions FAQs How does the charger work?How often must I charge the batteries? Daily UseWhy do my new batteries seem weak? Use these specifications to reorder deep-cycle batteriesHow can I get maximum range or distance per charge? What type of batteries should I use?How should I store my Power Chair and its batteries? How can I ensure maximum battery life?What about public transportation? What about shipping?Page I . O P E R a T I O N To select a speed setting Speed SettingsPower Accessories Power ModuleSleep Mode Actuator Lighting Module Not ShownTrouble Codes Other components are located inside the power base Motor wiring harnesses Battery wiring harnessesEuropa Master Remote JoystickTo enable the lockout system On/off key toggles the system power on and offOn/Off Key System Status LightDrive Mode and Actuator Display also Remote Status Display To change the drive mode programBattery Saver Feature Sleep Mode If EnabledFlash Code Sequence Diagnosis Solution Fault CodesShould your power chair come in contact with water Care and MaintenanceTemperature I I . C a R E a N D M a I N T E N a N C EWeekly Checks Daily ChecksTo check the brakes To calibrate the joystick Remote Plus onlyMonthly Checks Cleaning Precautions Tire/Wheel ReplacementYearly Checks StorageTo replace the batteries Battery ReplacementCorrective Maintenance Motor BrushesTo inspect or replace the motor brushes O P T I O N a L a C C E S S O R I E S Optional AccessoriesA R R a N T Y Lifetime Limited WarrantyT E S Remote Plus Controller Europa ControllerFit and Finish Performance Inclusion of all Parts
Related manuals
Manual 2 pages 44.46 Kb Manual 2 pages 57.43 Kb

1470, 1400, 1420 specifications

The Quantum 6000 XL, 1650, and 1420 are advanced models designed for high-performance applications, showcasing cutting-edge technologies and remarkable features. These machines are engineered to meet the demands of various industries, providing efficiency and precision in their operations.

Starting with the Quantum 6000 XL, this model stands out due to its enhanced processing capabilities, allowing it to handle complex tasks with ease. It is equipped with a high-speed processor and a robust memory architecture, enabling seamless multitasking and processing of large data sets. The XL version features a larger work area, making it ideal for projects that require extensive space and resources. Its advanced cooling system ensures optimal performance during prolonged use, minimizing thermal throttling and maximizing productivity.

The Quantum 1650 model is designed for versatility, offering a balance between performance and resource management. It incorporates energy-efficient technologies that lower operational costs without compromising output quality. With its intuitive user interface, operators can easily navigate through features and settings, enhancing workflow and reducing the learning curve. The 1650 is also equipped with modular components that can be upgraded or replaced, ensuring longevity and adaptability to future technological advancements.

Meanwhile, the Quantum 1420 model is tailored for compact environments where space is a premium. Despite its smaller footprint, it boasts powerful functionalities that rival larger machines. Features such as precision sensors and advanced software algorithms allow for accurate performance monitoring, ensuring that results consistently meet high standards. The 1420 is optimized for quick setup and teardown, making it a favorite for jobs that require agility and speed.

Common to all three models is their commitment to connectivity and integration. Equipped with multiple communication interfaces, they can seamlessly connect with various devices and networks, allowing for real-time data transfer and remote monitoring. Moreover, their compatibility with industry-standard software enhances their usability across different platforms.

In conclusion, the Quantum 6000 XL, 1650, and 1420 represent the forefront of technological innovation, each tailored to specific needs while sharing a foundation of robust performance, efficiency, and connectivity. These models are tailored for industries looking to leverage advanced machinery to boost productivity and operational efficiency.
Top Page Image Contents