Emerson KF140TZ00 owner manual How to Hang Your Ceiling Fan, How to Wire Your Ceiling Fan

How to Hang

Your Ceiling Fan

!WARNING

The fan must be hung with at least 7' of clearance from floor to blades (Figure 10).

CEILING

AT LEAST

7'

FLOOR

!WARNING

Hanger bracket must seat firmly against outlet box. If the outlet box is recessed, remove wall board until bracket contacts box. If bracket and/or outlet box are not securely attached, the fan could wobble or fall.

OUTLET

BOX

TWO SCREWS
SUPPLIED
WITH
OUTLET BOX	HANGER
	BRACKET
	TAB

How to Wire

Your Ceiling Fan

If you feel that you do not have enough electrical wiring knowledge or experi- ence, have your fan installed by a licensed electrician.

!WARNING

Turning off wall switch is not suffi- cient. To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring. All wiring must be in accordance with National and Local codes and the ceil- ing fan must be properly grounded as a precaution against possible electri- cal shock.

2. Refer to Figure 13 and 14 and connect the receiver wires to the supply wires and the fan motor wires as follows:

a. Securely connect the green grounding

wires from the hanger ball and the

hanger bracket to the supply grounding

conductor (this may be a bare wire or a

wire with green insulation).

b. Securely connect the supply white

(neutral) wire to the receiver white

(AC IN N) wire.

c. Securely connect the supply black wire

(hot) wire to the receiver black (AC IN

L) wire.

d. Securely connect the fan motor white

wire to the receiver white (TO MOTOR

N) wire.

e. Securely connect the fan motor black

wire to the receiver black (TO MOTOR

Figure 10

!WARNING

The outlet box and joist must be securely mounted and capable of supporting at least 50 lbs. Use only a U.L. outlet box listed as “Acceptable for Fan Support”.

Figure 11

2. Carefully lift the fan and seat the hang- er ball/downrod assembly on the hang- er bracket that was just attached to the outlet box (Figure 12). Be sure the groove in the ball is lined up with the tab on the hanger bracket (Figure 11).

CAUTION: To reduce the risk of electri- cal shock, disconnect the electrical supply circuit before installing the fan, light kit or receiver.

1. Position the supply wires to the left side of the outlet box (Figure 13); position the fan wires to the right side. Partially insert the remote control receiver (flat

L) wire.

f. Securely connect the fan motor blue

wire to the receiver blue (FOR

BOTTOM LIGHT) wire.

g. Securely connect the fan motor orange

wire to the receiver orange (FOR

UPPER LIGHT) wire.

!WARNING

To reduce the risk of fire, electric shock, or personal injury, mount fan to outlet box marked “Acceptable for Fan Support”, and use screws sup- plied with outlet box. Most outlet boxes commonly used for support of light fixtures are not acceptable for

!WARNING

Failure to seat tab in groove could cause damage to electrical wires and possible shock or fire hazard.

NOTE: CEILING COVER, SUPPLY WIRES AND FAN WIRES OMITTED FOR CLARITY.

side up) until one end rests on the hanger ball as shown in Figure 13.

NOTE: Make all wiring connections using wire connectors (supplied). Make sure that all connections are tight, including ground, and that no bare wire is visible at the wire connectors, except for the ground wire.

!WARNING

Check to see that all connections are tight, including ground, and that no bare wire is visible at the wire con- nectors, except for the ground wire. Do not operate fan until blades are in place. Noise and fan damage could result.

fan support and may need to be replaced. Consult a qualified electri- cian if in doubt.

1. Securely attach the hanger bracket to the outlet box using the two screws supplied with the outlet box (Figure 11).

Figure 12

OUTLET

BOX

HANGER

BRACKET

HANGER BALL/ DOWNROD ASSEMBLY

	SUPPLY WHITE WIRE		RECEIVER WHITE
	(NEUTRAL)		WIRE	RECEIVER BLACK WIRE
SUPPLY BLACK	A
	C I				RECEIVER BLACK
WIRE (HOT)	N	N
GROUND WIRE					WIRE		RECEIVER
							BLUE WIRE
				LIGHT	MOTOR	L	LIGHT
		AC IN L	N

!WARNING

To avoid possible fire or shock, do not pinch wires between the hanger ball/downrod assembly and hanger bracket.

8

GREEN GROUND WIRE	MOTOR	BOTTOM		UPPER	RECEIVER
FROM HANGER BALL			TO
				FOR
ANTENNA	TO	FOR			ORANGE WIRE
GREEN GROUND WIRE	FAN BLACK
FROM HANGER BRACKET	WIRE			FAN ORANGE
1-1/4" THREADED	FAN BLUE WIRE			WIRE
STUD (2)	FAN WHITE WIRE		RECEIVER WHITE
Figure 13	9		WIRE