Sears 315.17506, 315.17504 Switch Replacement, Model, See Figures 16and, Switch 1/32IN. Diameter

Page 17

ROUTING WITH GUIDE BUSHINGS

When using the Template Guide Bushings Item No. 9-25082 with your router, you must visually center the bit with the bushing before beginning your cut. You r router subbase may be adjusted by loosening the screws holding the subbase to your router. Be sure clamping lever is locked before center- ing bit in bushing. After centering bit with bushing, tighten screws firmly.

WARNING:

Failure to center bit with bushing or to firmly tighten screws after centering could cause bit to come in contact with bushing resulting in serious injury.

i

ROUTER TABLES

The use of Craftsman routers on router tables offered by other manufacturers has not been investigated for compli- ance with applicable safety standards.

WARNING:

Do not use with router tables that fail to conform to safe

wood working practices and offer proper guarding for the cutter. Failure to comply can result in an accident causing possible serious injury.

SWITCH REPLACEMENT

(MODEL

NO. 315.175040)

 

See Figures

16and

17.

 

UNPLUG

YOUR

ROUTER.

 

WARNING:

A

 

Failure to unplug your router could result in accidental

 

starting

causing serious injury.

 

Remove screws (A) and handle cover (B). See Figure

 

16.

 

 

 

 

Note the location of the molded bend relief (C) on

 

the power handle cord. Also note all wiring in the

 

handle and how each lead is connected to the

Fig. 16

switch. Connections and wiring position must be

 

identical when installing new switch. See Figure 16.

 

Remove leads from switch (D) by inserting a 1/32 in.

 

diameter nail or pin into switch lead receptacle and

 

pulling on lead as shown in figure 17. Remove nail or

 

pin with a twisting, pulling motion.

 

Make lead connections to new switch. Push each lead

 

as far as possible into proper switch receptacle. Pull on

 

leads to check lead connections with lead receptacles.

SWITCH 1/32IN. DIAMETER

Locate switch in handle and place leads so they won't

NAIL OR PIN

 

be pinched or contact screws when handle cover is

 

replaced.

 

 

Make sure molded bend relief (C) is correctly positioned

 

in switch handle, then replace handle cover and screws.

 

Tighten

all screws securely.

 

Page 17

Image 17
Contents CRRFTSMRNo Symbol Meaning Safety Alert Symbol Full ONE Year Warranty on Craftsman RouterElectrical Connection DeptMake Sure Your Extension Cord is Remove Adjusting Keys and WrenchesDo not USE Tool Under BROWN-OUT Rules for Safe OperationUnpacking Features Switch Lock-On Power Cord Collet HorsepowerNET Weight Depth of CUTDust BAG Assembly Variable Speed Switch with ElectronicSee Figures lb and lc See Figure lcUpside Down View of Router Depth Indicator PointKnow Your Router Wrench Spindle Depth AdjusngDepth Indicator Wrench Point Ring Blower Controlselector Depth Indicatorring SubbaseUnplug Your Router INSTALLING/REMOVINGCUTTERSLoci To Lock Pushin to To Unlock Spindle Lockand Unlock ColletIndicator Cutter Inside Subbase Cutterat Zero Depth of CUT AdjustmentsPractice Before Actual USE For Routertable Useonly Depth IndicatorringSee Figure Freehand Routing RoutingSpeed Selection Proper FeedingRate of Feed ForcefeedingDirection of Feed and Thrust Depth of CUTRouting PassWhole Edge Shaping Starting and Ending a CUTSwitch 1/32IN. Diameter Switch ReplacementModel See Figures 16andSee Figures 18 Switch Replacement ModelProper Care of Collet Proper Care of CuttersLubrication SeeGeneral Extension CordsCarbidetippedbits BIT QuarterPanel BIT Straight Bits Cutter Bevel Chamfer Round Groove Craftsman Router Model Number See Back page for Parts Ordering Instructions Key Part No. NumberSee Notea Parts List See Note Aj Description Quan HomeCentralSEARS