Sears 200.71233 owner manual Charging your battery outside the vehicle, Negative Positive

Page 12

Charging your battery outside the vehicle:

NOTE: A marine (boat) must be removed and charged on shore. To charge it on board requires equipment specially designed for marine use.

1.Remove battery from vehicle, making sure to dis- connect grounded terminal first with all power turned off to the vehicle.

2.Check the polarity of the battery posts as indicated on the battery case: POSITIVE (POS,P,+) and NEGATIVE (NEG,N,–).

NOTE: On top-post batteries, the positive battery terminal usually has a larger diameter than the negative one.

3.Connect the red (POSITIVE) charger clamp to the POSITIVE post of the battery. Be sure to rock the clamp back and forth to make a solid connection.

4.Attach at least a 6-gauge (AWG) insulated battery cable of at least 24-inches in length to the NEGA- TIVE battery post. This cable will provide a safer connection because any arcing and sparking will not occur directly over the battery. (The battery cable is not provided with the charger but may be purchased at most automotive accessory outlets.)

Negative

Positive (-)

(+)

5.Take the other end of the 6-gauge (AWG) insu- lated battery cable (at least 24-inches in length), and, standing as far away from the battery as possible, connect the black (NEGATIVE) charger clamp to the free end of the cable. Be sure to rock the clamp back and forth to make a solid connec- tion.

IMPORTANT: Wear safety glasses and face away from battery while you are making the final connection.

6.Make sure the power is set to the OFF position. Then, plug the power cord into a grounded 3- prong AC wall outlet.

7.Push the switch located on the front panel to

CHARGE.

8.Press the TIMER to the desired charge time, from 30-135 minutes. If more than 135 minutes of charging time is needed the hold position can be used. When using the HOLD feature the battery being charged must be monitored closely to avoid over-charging.

9.Press the VOLT/AMP SELECTOR to the desired charge position. (See “CHARGE RATE” chart on page 12 for correct settings.)

10.When the battery is fully charged, turn OFF the timer, then push the switch located on the front panel to OFF. Unplug the charger power cord from the wall outlet.

11.Face away from battery and remove the charger clamps from the NEGATIVE end of the cable first, then from the POSITIVE post.

12.Clean and store the battery charger.

11

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Battery Charger Table Of Contents WarrantyImportant Safety Instructions RememberWiring Diagram PartsBefore Using Your Battery Charger Assembling your chargerParts Tools Needed Plugging it HandleElectrical Shock Hazard Using an extension cord Preparing your battery to be chargedMaintenance and care Minimum Recommended Extension CordUsing Your Battery Charger Setting the controlsTimer To SET the TimerTimer Hold 12V ALTERNATOR/GENERATOR DisplayUsing the compressor Using the engine start featureEstimated Time for Inflating Charging Your Battery Charging your battery in the vehicleIs Normally the ONE That is Grounded Charging your battery outside the vehicle Negative PositiveChart Method Calculating charge timesHydrometer or Electronic Method Troubleshooting Problem Possible Cause SOLUTION/REASONSDisplay Mode Selec SEARS-64

200.71233 specifications

The Sears 200.71233 is a noteworthy model that exemplifies the brand's commitment to quality and functionality. Designed primarily for home improvement enthusiasts and DIYers, this versatile tool offers an impressive range of features that cater to a variety of tasks.

One of the standout characteristics of the Sears 200.71233 is its powerful motor, which enhances performance and efficiency. The tool is equipped with an easy-to-use user interface that allows for seamless adjustments, making it suitable for both novice users and seasoned professionals alike. Its compact design ensures that it remains portable, enabling users to transport it easily between job sites or storage areas.

The Sears 200.71233 showcases a host of innovative technologies aimed at enhancing user experience and overall functionality. The inclusion of advanced safety features is noteworthy; these mechanisms ensure that the tool operates safely while minimizing the risk of accidents. The ergonomic design further promotes comfort during extended use, allowing users to tackle tasks without excessive strain.

Another impressive aspect of the Sears 200.71233 is its versatility. The tool comes with an array of attachments and accessories that expand its capabilities, allowing users to perform different types of jobs such as cutting, grinding, and polishing. This multifunctionality eliminates the need for multiple tools, making it a cost-effective choice for those who need a single solution for various tasks.

Additionally, the durability of the Sears 200.71233 cannot be overlooked. Constructed from high-quality materials, this tool is designed to withstand the rigors of regular use. Its robust build not only enhances longevity but also ensures consistent performance over time, making it a reliable investment for users seeking a dependable tool.

In summary, the Sears 200.71233 embodies an array of features and technologies that make it a standout choice for home improvement projects. With its powerful motor, user-friendly design, safety features, and versatility, the tool is well-equipped to meet the demands of diverse applications. Whether tackling minor repairs or engaging in larger construction projects, users can rely on the Sears 200.71233 as an essential addition to their toolkit. Its combination of quality and innovation has solidified its place as a favored option among DIY enthusiasts and professionals alike.
Top Page Image Contents