12V ALTERNATOR/GENERATOR Display, Timer

12V ALTERNATOR/GENERATOR DISPLAY

14 –	15 volts	=	Good condition
12.8 or less volts		=	Check with qualified
			technician
12.8	- 14 volts or	=	See vehicle owner’s
15 volts or more			manual

NOTE: If the digital display reads less than 12.8 volts, the charging system may have loose fan belts, a defective voltage regulator or alternator. Additional tests may be required to find the exact cause. Take the vehicle to a qualified service center.

6V ALTERNATOR/GENERATOR DISPLAY

7 – 7.5 volts	=	Good condition
6.4 or less volts	=	Check with qualified
		technician
6.4 - 7 volts or	=	See vehicle owner’s
7.5 volts or more		manual

VOLT AND CHARGE RATE SELECTOR

The VOLT AND CHARGE RATE SELECTOR allows you to select the correct battery voltage and amp draw rate to match your charging needs. Read the following operating instructions for making the proper settings for charging a battery.

When you first start charging a battery, the amp reading will be high. As the battery becomes charged, the reading will decrease.

To determine the amount of amps being drawn by the battery:

1.Press the DISPLAY MODE button until the AMPS LED lights.

a.As the battery charges at 50 amps, the reading will decrease to 15 or 20 amps at full charge. You should stop charging the battery at this time.

b.When charging at 15 amps, the display should show 15 amps for a discharged battery and 7-8 amps for a fully charged battery. You should stop charging the battery at this time.

c.At the 2 amp charge rate, little or no display

change will occur.

NOTE: The digital display will read OLor Overload if more than 50 Amps are supplied to the battery. Overload means too high a charging rate. Lower the charging rate to continue.

To determine an accurate reading of your battery’s voltage before you charge:

1.Push the switch located on the front panel CHARGE SELECTOR/AIR COMPRESSOR to

CHARGE.

2.Press the DISPLAY MODE button so the VOLT- AGE LED lights.

3.Connect the battery charger as outlined in “Charg- ing Your Battery” on page 10. The voltage will be displayed.

NOTE: If a battery has recently been charged or in a vehicle that has been run recently, turn on the vehicle’s headlights for a few minutes before reading the meter to avoid getting a false reading from a surface charge.

4.Turn off vehicle’s headlights and read the digital display.

5.To turn OFF the charger, push the switch located on the front panel to OFF. The charger will shut off.

6.Unplug the power cord from the AC wall outlet.

7.Disconnect the battery charging clamps as out- lined in “Charging Your Battery” on page 10.

TIMER

The timer is designed to allow the battery to be charged for a designated amount of time. To accu- rately charge your battery, you must know the size of the battery in ampere hours or reserve capacity in units, as well as the state of charge. Since this infor- mation is not known by the charger, the timer limit is set at 2.25 hours to prevent the battery from over- charging to a point where it can be severely damaged. If you do not know the charge state of your battery, set the timer at one hour or less.

TO SET THE TIMER:

1.Press the symbol for less time and the symbol for more time.

2.The Timer LED will light and digital display will show the time in minutes.

3.To turn the timer off, press the symbol until the digital display reads OFF, or, push the CHARGE SELECTOR/AIR COMPRESSOR switch to OFF.

TIMER HOLD

The Timer Hold feature overrides the timer allowing the charger to continue charging for over 2.25 hours. This feature is most often used when the charging rate is 2 or 15 amps. Using this feature requires closely monitoring the charge time and turning off the charger when the battery is fully charged.

NOTE: When the battery is fully charged, the charger and timer will NOT automatically turn off. It is impor- tant to monitor the charge level. Not doing so may cause damage to your battery.

To activate the hold feature:

1.Press the symbol until the Digital Display reads

HLD.

2.To release the Timer Hold, press the until the digital display reads OFF or, push the CHARGE SELECTOR/AIR COMPRESSOR switch to OFF.

DIGITAL

DISPLAY

3-WAY

SWITCH

200.71233 specifications

The Sears 200.71233 is a noteworthy model that exemplifies the brand's commitment to quality and functionality. Designed primarily for home improvement enthusiasts and DIYers, this versatile tool offers an impressive range of features that cater to a variety of tasks.

One of the standout characteristics of the Sears 200.71233 is its powerful motor, which enhances performance and efficiency. The tool is equipped with an easy-to-use user interface that allows for seamless adjustments, making it suitable for both novice users and seasoned professionals alike. Its compact design ensures that it remains portable, enabling users to transport it easily between job sites or storage areas.

The Sears 200.71233 showcases a host of innovative technologies aimed at enhancing user experience and overall functionality. The inclusion of advanced safety features is noteworthy; these mechanisms ensure that the tool operates safely while minimizing the risk of accidents. The ergonomic design further promotes comfort during extended use, allowing users to tackle tasks without excessive strain.

Another impressive aspect of the Sears 200.71233 is its versatility. The tool comes with an array of attachments and accessories that expand its capabilities, allowing users to perform different types of jobs such as cutting, grinding, and polishing. This multifunctionality eliminates the need for multiple tools, making it a cost-effective choice for those who need a single solution for various tasks.

Additionally, the durability of the Sears 200.71233 cannot be overlooked. Constructed from high-quality materials, this tool is designed to withstand the rigors of regular use. Its robust build not only enhances longevity but also ensures consistent performance over time, making it a reliable investment for users seeking a dependable tool.

In summary, the Sears 200.71233 embodies an array of features and technologies that make it a standout choice for home improvement projects. With its powerful motor, user-friendly design, safety features, and versatility, the tool is well-equipped to meet the demands of diverse applications. Whether tackling minor repairs or engaging in larger construction projects, users can rely on the Sears 200.71233 as an essential addition to their toolkit. Its combination of quality and innovation has solidified its place as a favored option among DIY enthusiasts and professionals alike.