Husqvarna YTH2242TDRF To Move Forward and Backward See Fig, To USE Cruise Control J See Fig

Page 10

OPERATION

TO MOVE FORWARD AND BACKWARD (See Fig. 7)

The direction and speed of movement is controlled by the forward and reverse drive pedals.

Start tractor and release parking brake.

Slowly depress forward (K) or reverse (L) drive pedal to begin movement. Ground speed increases the further down the pedal is depressed.

K

J

L

Fig. 7

TO USE CRUISE CONTROL (J) (See Fig. 7)

The cruise control feature can be used for forward travel only.

SYSTEM CHARACTERISTICS

The cruise control should only be used while mowing or transporting on relatively smooth, straight surfaces. Other conditions such as trimming at slow speeds may cause the cruise control to disengage. Do not use the cruise control on slopes, rough terrian or while trimmimg or turning.

With forward drive pedal depressed to desired speed, pull cruise control lever (J) up and hold while lifting your foot off the pedal, then release the lever.

To disengage the cruise control, depress the brake pedal or tap on forward drive pedal.

TO ADJUST MOWER CUTTING HEIGHT (See Fig. 8)

The position of the attachment lift lever (A) determines the cutting height.

A

Fig. 8

Put attachment lift lever in desired cutting height slot.

The cutting height range is approximately 1" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.

The average lawn should be cut to approximately 2-1/2" during the cool season and to over 3" during hot months. For healthier and better looking lawns, mow often and after moderate growth.

For best cutting performance, grass over 6" in height should be mowed twice. Make the first cut relatively high; the second to desired height.

TO ADJUST GAUGE WHEELS (See Fig. 9)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE: Adjust gauge wheels with tractor on a flat level surface.

Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in this section of manual).

With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole. Tighten securely.

Repeat for all, installing gauge wheel in same adjust- ment hole.

9/16”

3/4”

Fig. 9

TO OPERATE MOWER

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. You must remain fully and centrally positioned in the seat to prevent the engine from hesitat- ing or cutting off when operating your equipment on rough, rolling terrain or hills.

Select desired height of cut. (See "TO ADJUST MOWER CUTTING HEIGHT".)

Start mower blades by engaging attachment clutch control.

10

Image 10
Contents YTH2242TDRF Safety Rules Safe Operation Practices for Ride-On MowersIII. Children General ServiceSafe Handling of Gasoline Table of Contents Unassembled Parts AssemblyTools Required for Assembly ToremovetractorfromcartonCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor Stopping See Fig HOW to USE Your TractorTo SET Parking BRAKESee Fig To USE Throttle Control D SeeTo Move Forward and Backward See Fig To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To USE Cruise Control J See FigReverse Operation System ROS Service REMINDER/HOUR MeterTo Stop Mower Blades To Operate on HillsCheck Engine OIL Level Battery INDICATOR/CHARGING Plug See FigBefore Starting the Engine ADD GasolinePurge Transmission To Start Engine See FigAutomatic Transmission Warm UP Mowing Tips Lubrication Chart MaintenanceMaintenance Schedule General RecommendationsBlade Care BatteryTractor Blade Removal See FigBelts Transaxle MaintenanceEngine Transaxle Pump FluidCleaning Deck Washout Port See Fig To Install Mower See Figs Service and AdjustmentsTo Remove Mower See Fig Raise attachment lift lever to highest position To Level Mower To Replace Mower Blade Drive Belt To Check BrakeFront Wheel TOE-IN/CAMBER To Start Engine with a Weak Battery See FigTo Replace Motion Drive Belt See Fig To Remove Wheel for Repairs See FigTransmission Fuel System StorageOther Engine OILTroubleshooting Problem Cause CorrectionEngine continues to Service Notes Wheels and Tires DecalsKEY Part Description Schematic SCH12Tractor Model NO. YTH2242TDRF 96041023700, Product no 41 ElectricalKEY Part Description Chassis Tractor Model NO. YTH2242TDRF 96041023700, Product no 41 Drive 183 532 13 Spacer Split Spark Arrester KIT EngineEngine Power Rating Information Steering Assembly 532 43 Wheel, Steering Seat Assembly 532 43 SeatMower Lift  Mower Deck Tractor Model NO. YTH2242TDRF 96041023700, Product no 41 Service Notes Suggested Guide for Sighting Slopes for Safe Operation 01.22.14 JM