Hobart 652 manual Principal Safety Standards

Page 7

1-3. Additional Symbols for Installation, Operation, and Maintenance

FIRE OR EXPLOSION hazard.

D Do not install or place unit on, over, or near combustible surfaces.

DDo not install unit near flammables.

DDo not overload building wiring – be sure power supply system is properly sized, rated, and protected to handle this unit.

MOVING PARTS can cause injury.

DKeep away from moving parts such as fans.

DKeep all doors, panels, covers, and guards closed and securely in place.

FALLING UNIT can cause injury.

DUse lifting eye to lift unit only, NOT running gear, gas cylinders, or any other accessories.

DUse equipment of adequate capacity to lift and support unit.

DIf using lift forks to move unit, be sure forks are long enough to extend beyond opposite side of unit.

OVERUSE can cause OVERHEATING

DAllow cooling period; follow rated duty cycle.

DReduce current or reduce duty cycle before starting to weld again.

DDo not block or filter airflow to unit.

H.F. RADIATION can cause interference.

DHigh-frequency (H.F.) can interfere with radio navigation, safety services, computers, and communications equipment.

DHave only qualified persons familiar with electronic equipment perform this installation.

DThe user is responsible for having a qualified electrician prompt- ly correct any interference problem resulting from the installa- tion.

DIf notified by the FCC about interference, stop using the equipment at once.

DHave the installation regularly checked and maintained.

DKeep high-frequency source doors and panels tightly shut, keep spark gaps at correct setting, and use grounding and shielding to minimize the possibility of interference.

STATIC (ESD) can damage PC boards.

DPut on grounded wrist strap BEFORE handling boards or parts.

DUse proper static-proof bags and boxes to store, move, or ship PC boards.

MOVING PARTS can cause injury.

DKeep away from moving parts.

DKeep away from pinch points such as drive rolls.

WELDING WIRE can cause injury.

DDo not press gun trigger until instructed to do so.

DDo not point gun toward any part of the body, other people, or any metal when threading welding wire.

ARC WELDING can cause interference.

DElectromagnetic energy can interfere with sensitive electronic equipment such as computers and computer-driven equipment such as robots.

DBe sure all equipment in the welding area is electromagnetically compatible.

DTo reduce possible interference, keep weld cables as short as possible, close together, and down low, such as on the floor.

DLocate welding operation 100 meters from any sensitive elec- tronic equipment.

DBe sure this welding machine is installed and grounded according to this manual.

DIf interference still occurs, the user must take extra measures such as moving the welding machine, using shielded cables, using line filters, or shielding the work area.

1-4. Principal Safety Standards

Safety in Welding and Cutting, ANSI Standard Z49.1, from American Welding Society, 550 N.W. LeJeune Rd, Miami FL 33126

Safety and Health Standards, OSHA 29 CFR 1910, from Superinten- dent of Documents, U.S. Government Printing Office, Washington, D.C. 20402.

Recommended Safe Practices for the Preparation for Welding and Cut- ting of Containers That Have Held Hazardous Substances, American Welding Society Standard AWS F4.1, from American Welding Society, 550 N.W. LeJeune Rd, Miami, FL 33126

National Electrical Code, NFPA Standard 70, from National Fire Protec- tion Association, Batterymarch Park, Quincy, MA 02269.

Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet P-1, from Compressed Gas Association, 1235 Jefferson Davis Highway, Suite 501, Arlington, VA 22202.

Code for Safety in Welding and Cutting, CSA Standard W117.2, from Canadian Standards Association, Standards Sales, 178 Rexdale Boulevard, Rexdale, Ontario, Canada M9W 1R3.

Safe Practices For Occupation And Educational Eye And Face Protection, ANSI Standard Z87.1, from American National Standards Institute, 1430 Broadway, New York, NY 10018.

Cutting And Welding Processes, NFPA Standard 51B, from National Fire Protection Association, Batterymarch Park, Quincy, MA 02269.

OM-278 Page 3

Image 7
Contents Processes OM-278Description From Hobart to You Table of Contents Page Electric Shock can kill Symbol UsageMarks a special safety message Arc Welding HazardsBuildup of GAS can injure or kill ARC Rays can burn eyes and skinWelding can cause fire or explosion Flying Metal can injure eyesPrincipal Safety Standards About Pacemakers EMF InformationIdentifie un message de sécurité particulier Signification des symbolesUN Choc Électrique peut tuer LES Fumées ET LES GAZ peuvent être dangereuxLE Bruit peut affecter l’ouïe LE Soudage peut provoquer un incendie ou une explosionDES Particules Volantes peuvent blesser les yeux DES Pièces Chaudes peuvent pro- voquer des brûlures gravesDES Organes Mobiles peuvent provoquer des blessures Risque D’INCENDIE OULA Chute DE L’APPAREIL peut blesser ’EMPLOI Excessif peutInformation sur les champs électromagnétiques Principales normes de sécuritéConsignes relatives aux stimulateurs cardiaques Definitions General Precautionary Label? a Nameplate Safety SymbolsInput Connection Label Electric Shock And Airflow LabelManufacturer’s Rating Label For CE Products Rating InstallationSymbols And Definitions SpecificationsOverheating CC Mode CV ModeDuty Cycle And Overheating Volt-Ampere CurvesSelecting a Location Dimensions And WeightsMovement Location And Airflow VAC Receptacle And Circuit Breakers Be careful when placing or moving unit over uneven surfacesTurn Off power before connecting to receptacle TippingRemote 14 Receptacle And Terminal Strip 1T Information Weld Output Terminals And Selecting Cable SizesOror Connecting Remote ControlElectrical Service Guide Do not overtighten jumper link nuts Placing Jumper Links And Connecting Input PowerControls Non CE Models OperationControls CE Models Months Maintenance & TroubleshootingRoutine Maintenance Fuse F1Trouble Remedy TroubleshootingOM-278 Circuit Diagram Electrical DiagramMain Assembly 652 Model Illustrated Parts ListPLG13 Panel, Front w/Components -1 Item PC2 Rectifier, Si Diode -1 Item Panel, Rear w/Components -1 Item Page Page Page Support ServiceHobart Welding Products Contact your Distributor for

652 specifications

Hobart 652 is a sophisticated piece of catering equipment designed to enhance food preparation and cooking efficiency in commercial kitchens. Known for its robust construction and user-friendly features, the Hobart 652 stands out as a versatile machine suitable for various food service environments, including restaurants, hotels, and catering companies.

One of the main features of the Hobart 652 is its powerful mixing capabilities. Equipped with a heavy-duty motor, it can handle even the most challenging mixing tasks, from bread dough to cake batter. The machine offers multiple speed settings, allowing users to tailor the mixing process according to specific recipes and requirements. This flexibility ensures optimal results for various culinary applications.

The design of the Hobart 652 prioritizes ease of use and safety. The control panel is intuitively laid out, enabling operators to adjust settings quickly and efficiently. Additionally, the machine features safety interlocks that prevent operation when components are not securely in place, promoting a safer working environment. The durable construction, made from high-quality stainless steel, not only enhances longevity but also facilitates easy cleaning, meeting the stringent hygiene standards of commercial kitchens.

Another notable characteristic of the Hobart 652 is its versatility. It comes with a range of attachments that enable it to perform various tasks, such as slicing, shredding, and grating, thereby replacing multiple pieces of equipment. This multi-functionality can significantly save space and reduce costs for kitchen operators.

In terms of technology, the Hobart 652 incorporates advanced engineering that optimizes performance while minimizing energy consumption. This innovative approach aids in reducing operational costs, making it a preferred choice for eco-conscious businesses. The quiet operation of the machine also contributes to a more pleasant working atmosphere, enhancing overall staff efficiency.

Overall, the Hobart 652 is an integral asset for commercial kitchens, combining power, versatility, and advanced technology. Its numerous features and characteristics make it well-suited for professional chefs and kitchen staff, contributing to seamless food preparation and high-quality culinary output. As the demand for efficient kitchen equipment continues to grow, the Hobart 652 remains a reliable and effective solution for food service operations.