Hobart Welding Products OM-180 670Q manual Principal Safety Standards

Page 7

1-3. Additional Symbols For Installation, Operation, And Maintenance

FIRE OR EXPLOSION hazard.

D Do not install or place unit on, over, or near combustible surfaces.

DDo not install unit near flammables.

DDo not overload building wiring – be sure power supply system is properly sized, rated, and protected to handle this unit.

MOVING PARTS can cause injury.

DKeep away from moving parts such as fans.

DKeep all doors, panels, covers, and guards closed and securely in place.

FALLING UNIT can cause injury.

DUse lifting eye to lift unit only, NOT running gear, gas cylinders, or any other accessories.

DUse equipment of adequate capacity to lift and support unit.

DIf using lift forks to move unit, be sure forks are long enough to extend beyond opposite side of unit.

OVERUSE can cause OVERHEATING

DAllow cooling period; follow rated duty cycle.

DReduce current or reduce duty cycle before starting to weld again.

DDo not block or filter airflow to unit.

H.F. RADIATION can cause interference.

DHigh-frequency (H.F.) can interfere with radio navigation, safety services, computers, and communications equipment.

DHave only qualified persons familiar with electronic equipment perform this installation.

DThe user is responsible for having a qualified electrician prompt- ly correct any interference problem resulting from the installa- tion.

DIf notified by the FCC about interference, stop using the equipment at once.

DHave the installation regularly checked and maintained.

DKeep high-frequency source doors and panels tightly shut, keep spark gaps at correct setting, and use grounding and shielding to minimize the possibility of interference.

STATIC (ESD) can damage PC boards.

DPut on grounded wrist strap BEFORE handling boards or parts.

DUse proper static-proof bags and boxes to store, move, or ship PC boards.

MOVING PARTS can cause injury.

DKeep away from moving parts.

DKeep away from pinch points such as drive rolls.

WELDING WIRE can cause injury.

DDo not press gun trigger until instructed to do so.

DDo not point gun toward any part of the body, other people, or any metal when threading welding wire.

ARC WELDING can cause interference.

DElectromagnetic energy can interfere with sensitive electronic equipment such as computers and computer-driven equipment such as robots.

DBe sure all equipment in the welding area is electromagnetically compatible.

DTo reduce possible interference, keep weld cables as short as possible, close together, and down low, such as on the floor.

DLocate welding operation 100 meters from any sensitive elec- tronic equipment.

DBe sure this welding machine is installed and grounded according to this manual.

DIf interference still occurs, the user must take extra measures such as moving the welding machine, using shielded cables, using line filters, or shielding the work area.

1-4. Principal Safety Standards

Safety in Welding and Cutting, ANSI Standard Z49.1, from American Welding Society, 550 N.W. LeJeune Rd, Miami FL 33126

Safety and Health Standards, OSHA 29 CFR 1910, from Superinten- dent of Documents, U.S. Government Printing Office, Washington, D.C. 20402.

Recommended Safe Practices for the Preparation for Welding and Cut- ting of Containers That Have Held Hazardous Substances, American Welding Society Standard AWS F4.1, from American Welding Society, 550 N.W. LeJeune Rd, Miami, FL 33126

National Electrical Code, NFPA Standard 70, from National Fire Protec- tion Association, Batterymarch Park, Quincy, MA 02269.

Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet P-1, from Compressed Gas Association, 1235 Jefferson Davis Highway, Suite 501, Arlington, VA 22202.

Code for Safety in Welding and Cutting, CSA Standard W117.2, from Canadian Standards Association, Standards Sales, 178 Rexdale Boulevard, Rexdale, Ontario, Canada M9W 1R3.

Safe Practices For Occupation And Educational Eye And Face Protection, ANSI Standard Z87.1, from American National Standards Institute, 1430 Broadway, New York, NY 10018.

Cutting And Welding Processes, NFPA Standard 51B, from National Fire Protection Association, Batterymarch Park, Quincy, MA 02269.

OM-180 670 Page 3

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Processes OM-180 670QDescription From Hobart to You Table of Contents Standards DirectivesElectric Shock can kill Symbol UsageMarks a special safety message Arc Welding HazardsBuildup of GAS can injure or kill ARC Rays can burn eyes and skinWelding can cause fire or explosion Flying Metal can injure eyesPrincipal Safety Standards About Pacemakers EMF InformationLES Fumé ES ET LES GAZ peuvent ê tre dangereux Signification des symbolesConsignes DE Securite Lire Avant Utilisation UN Choc É Lectrique peut tuerDES Particules Volantes peuvent blesser les yeux LE Soudage peut provoquer un incendie ou une explosionLE Bruit peut affecter l’ouïe DES Organes Mobiles peuvent provoquer des blessures Risque D’INCENDIE OULA Chute DE L’APPAREIL peut blesser ’EMPLOI Excessif peutInformation sur les champs é lectromagné tiques Principales normes de sé curitéConsignes relatives aux stimulateurs cardiaques Manufacturer’s Warning Label Definitions Definitions60 s Manufacturer’s Rating Labels I1max Symbols And DefinitionsI1eff Specifications InstallationDuty Cycle And Overheating CV Mode CC ModeVolt-Ampere Curves Movement Dimensions And WeightDo not move or operate unit where it could tip Selecting a Location45 m 60 m 70 m 90 m 105 m Weld Output Terminals And Selecting Cable SizesARC Welding can cause Electromagnetic Interference 150 ft 200 ft 250 ftVolt AC Duplex Receptacle Remote 14 Receptacle InformationSocket Connecting Input Power Electrical Service GuideFront Panel Controls OperationMeter Functions PPPMode Output Control Mode Switch SettingsLift-Arc Trigger Hold TIG Procedure requiresDo not remove case when blowing out inside of unit Maintenance & TroubleshootingBlowing Out Inside Of Unit Voltmeter/Ammeter Help Displays HE.L P-9Trouble Remedy TroubleshootingOM-180 670 Circuit Diagram For Welding Power Source Electrical DiagramParts Assembly Parts ListDia Part 173 Support ServiceHobart Welding Products Contact your Distributor for

OM-180 670Q specifications

The Hobart Welding Products OM-180 670Q is a versatile and reliable welding machine designed to meet the needs of both professional welders and DIY enthusiasts. Known for its user-friendly features and robust performance, the OM-180 670Q stands out in the market for its exceptional build quality and innovative technologies.

One of the main features of the OM-180 670Q is its MIG welding capability, which allows for precise and efficient welding on a variety of materials, including mild steel, stainless steel, and aluminum. This makes it suitable for a broad range of applications, from auto body repairs to light industrial work. The welding machine operates on a 230V power supply, providing the flexibility needed for both home workshops and professional environments.

The device is equipped with a smooth and adjustable wire feed speed control, enabling welders to easily fine-tune their settings for optimal bead appearance and penetration. This feature ensures that users can achieve consistent results, regardless of the specific project requirements. Additionally, the OM-180 670Q includes a dual-gauge regulator, which allows for precise monitoring of gas flow, ensuring weld quality and reducing waste.

Another notable characteristic of the OM-180 670Q is its compact and portable design. The lightweight construction, combined with a built-in handle, makes it easy for users to transport the machine to different job sites or store it away when not in use. This portability does not compromise the durability of the product; the rugged outer shell is designed to withstand the rigors of daily use.

The Hobart OM-180 670Q also incorporates technological advancements such as the Auto-Set feature, which simplifies the setup process by automatically adjusting voltage and wire feed speed based on the selected material thickness. This takes the guesswork out of welding, making it accessible for novice welders while still offering flexibility for experienced users.

Safety is another critical aspect of the OM-180 670Q. It includes built-in safety features such as thermal overload protection, which prevents overheating, and a built-in fan to maintain optimal operating temperatures. Furthermore, its simplicity in design with fewer controls means that operators can focus on their skills without being overwhelmed by complex settings.

In summary, the Hobart Welding Products OM-180 670Q is a well-rounded welding machine that combines ease of use, advanced technology, and portability. Its ability to handle various materials, along with safety and precision features, makes it an excellent choice for both beginners and seasoned welders looking for a reliable tool for their projects.
Top Page Image Contents