Harbor Freight Tools 45861 Specifications, Unpacking, Instructions for putting into use, Mounting

Page 9

Specifications

Electrical Requirements

120 V~ / 60 Hz

 

 

Lathe Type

Metal Cutting

 

 

Motor

3/4 HP

 

 

Motor Speed

1790 RPM

 

 

Spindle Speed

120, 320, 420, 620,

1130 & 2000

 

Spindle Taper

MT-3

Spindle Bore

3/4”

Chuck

3 Jaw

Chuck Capacity

4”

Tail Stock Quill Travel

1-3/4”

Tail Stock Quill Taper

MT-2

Tool Post Capacity

3/4”

Swing Over Bed

9”

Distance Between Centers

20”

Unpacking

When unpacking, check to make sure that the item is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible.

Proper lubrication is essential. To be safe, and to become more familiar with the Lathe, disassemble the lathe entirely, then clean and lubricate each part with white lithium grease before first use.

List of contents

Part(s)

Description

Qty

 

9” X 20” Bench Lathe

1

 

4” 3-Jaw Chuck

1

 

Reverse Jaws For Chuck.

3

 

Chuck Wrench

1

 

Dead Center Mt#2

1

 

Dead Center Mt#3

1

 

Live Center

1

 

10-12 Open-End Wrench

1

 

14-17 Open-End Wrench

1

Part(s)

Description

Qty

 

17-19 Open-End Wrench

1

 

Round Nut Wrench 45-52

1

 

Tool Post Wrench

1

 

Hex Wrenches - 3, 4, 5, 6mm

1 ea.

 

Drive Belts

2

 

Threading Gear Set 28,30,

1

 

36,42,45 & 80T

 

 

Oil Can

1

 

Splash Guard

1

 

Operators Manual

1

Instructions for putting into use

Read the entire Important Safety Information section at the beginning of this manual including all text under subheadings therein before set up or use of this product.

To prevent serious injury

from accidental operation:

Turn the Power Switch of the tool to its “OFF” position and unplug the tool from its electrical outlet before assembling or making any adjustments to the tool.

Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual.

Mounting

1.Unbolt and remove the Lathe from the crate.

2.The Lathe will need to be mounted to a surface capable of bearing the combined weight of the Lathe and intended workpieces. The surface

SKU 45861

For technical questions, please call 1-800-444-3353.

Page 9

Image 9
Contents Distributed exclusively by Harbor Freight Tools For technical questions or replacement parts, please callContents Save This Manual General Power Tool SafetyGfci reduces the risk of electric shock Lathe Safety Warnings Grounding Grounded Tools Tools with Three Prong PlugsProng Plug and Outlet Outlet Extension CordsPlug and Outlet See Table aSymbology List of contents SpecificationsUnpacking Instructions for putting into useWorkpiece and Work Area Set Up Tool Set UpRead the entire Important Safety Information section Operating InstructionsSKU For technical questions, please call LatheDefinition of Terms Installing a Chuck Live Center Spindle SpeedsSteady Rest Follow RestDirection Switch Belt Tension Lever General Operating Instructions General Milling GuidelinesFacing Operations Drilling Thread Cutting TurningCleaning and Maintenance Lubrication Maintenance ServicingPlease Read the Following Carefully Headstock diagram Headstock Parts ListPart Description Qty Record Product’s Serial Number HereDrive Parts List Drive diagram Tensioning roller Parts List Quadrant Parts List Motor housing Parts List Bed Parts List Gear box Parts List Gear box diagram Apron Parts List Apron Parts List Saddle and cross slide Parts List Saddle and cross slide diagram Tailstock Parts List Tailstock diagram Travelling rest Parts List Steady Rest Parts List Wiring diagram Wiring diagram Limited 1 year / 90 day Warranty