least the minimum wire size required.
(See Table A.)
4.If you are using one extension cord for more than one tool, add the nameplate amperes and use the sum to determine the required minimum cord size. (See Table A.)
5.If you are using an extension cord outdoors, make sure it is marked with the suffix
6.Make sure the extension cord is prop- erly wired and in good electrical con- dition. Always replace a damaged extension cord or have it repaired by a qualified electrician before using it.
7.Protect the extension cords from sharp objects, excessive heat, and damp or wet areas.
RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS*
(110 VOLT)
NAMEPLATE | EXTENSION CORD | ||||||
| LENGTH |
| |||||
AMPERES |
|
| |||||
25’ | 50’ | 75’ | 100’ | 150’ | |||
(at full load) | |||||||
|
|
|
|
| |||
|
|
|
|
|
| ||
0 – 2.0 | 18 | 18 | 18 | 18 | 16 | ||
2.1 | – 3.4 | 18 | 18 | 18 | 16 | 14 | |
3.5 | – 5.0 | 18 | 18 | 16 | 14 | 12 | |
5.1 | – 7.0 | 18 | 16 | 14 | 12 | 12 | |
7.1 – 12.0 | 18 | 14 | 12 | 10 | - | ||
12.1 | – 16.0 | 14 | 12 | 10 | - | - | |
16.1 | – 20.0 | 12 | 10 | - | - | - | |
TABLE A | * Based on limiting the line | ||||||
voltage drop to five volts at | |||||||
150% of the rated amperes.
Symbology
Double Insulated
| Canadian Standards Association |
|
|
| Underwriters Laboratories, Inc. |
|
|
V~ | Volts Alternating Current |
A | Amperes |
| |
|
|
n0 xxxx/min. | No Load Revolutions per Minute |
(RPM) |
Specifications
| 110 V~ / 60 Hz | |
Electrical | Power Cord: 18 AWG X 3C | |
Requirements | Power Plug: | |
| 7.5 A | |
Maximum Stock | 18” Long, 10” Diameter | |
Length/Diameter | ||
| ||
Lathe Type | Wood Cutting | |
|
| |
Motor | 1/2 HP | |
|
| |
Motor Speed | 1700 RPM | |
|
| |
Spindle Speeds | 750, 1100, 1600, 2200, 3200 | |
(RPM) | ||
| ||
Spindle Run Out | 0.0025” | |
|
| |
Tail Stock | 2” | |
Quill Travel | ||
| ||
Tail Stock | ||
Quill Taper | ||
| ||
Tool Rest Length | 7” | |
|
| |
Tool Rest Capacity | 2” | |
|
| |
Faceplate Size | 3” | |
|
| |
Drive Method | Belt & Pulley | |
|
| |
Belt Type | ||
|
| |
| Safety Goggles (Qty. 1) | |
| 3mm, 6mm, 8mm Hex Wrench (1 ea.) | |
Accessories | Faceplate & Spindle Nut (1 ea.) | |
| Live Center & Spur Center (1 ea.) | |
| Tool Rest (Qty. 1) |
REV 09e
SKU 65345 | For technical questions, please call | Page 8 |