Grizzly G0657/G0658 owner manual Spindle Turning, To set up a spindle turning operation

Page 27

Spindle Turning

Spindle turning (Figure 34) is the operation per- formed when a workpiece is mounted between the headstock and the tailstock.

Figure 34. Typical spindle turning operation.

To set up a spindle turning operation:

1.Mark both ends of your workpiece by draw- ing diagonal lines from corner to corner. The intersection point of these lines will show you the center of your workpiece. See Figure 35 for details.

���������

������������

�����������������

��������������

���������

������

Figure 35. Workpiece marked diagonally from

corner to corner to determine the center.

G0657/G0658 Benchtop Lathe

2.Using a wood mallet, tap the point of the spur center into the center of the workpiece, so that it leaves a center mark, then remove the spur center.

3.Using a 18" drill bit, drill a 316" deep hole at the center mark.

4.Cut the corners off your workpiece if it is over 2" x 2" to make turning safer and easier.

5.Drive the spur center into the center of the workpiece with a wood mallet to embed it at least 14", as shown in Figure 36.

����

Figure 36. Spur center properly embedded.

6.With the workpiece still attached, insert the spur center into the headstock spindle.

7.With the live center installed in the tailstock, slide the tailstock toward the workpiece until the live center touches the workpiece center- point, then lock the tailstock in this position.

8.Use the quill handwheel to push the live cen- ter into the workpiece at least 14".

Do not press the workpiece too firmly with the tailstock or the bearings will bind and overheat. Likewise, do not leave it too loose or the workpiece will spin off the lathe. Use good judgement. Serious personal injury could result if care is not taken.

-25-

Image 27
Contents Benchtop Lathe Page Table of Contents Introduction Foreword Functional OverviewContact Info G0657/G0658 Identification G0657/G0658 Benchtop Lathe G0657/G0658 Benchtop Lathe G0657/G0658 Benchtop Lathe G0657/G0658 Benchtop Lathe G0657/G0658 Benchtop Lathe G0657/G0658 Benchtop Lathe Additional Safety for Wood Lathes 110V Operation Circuit RequirementsAdditional Contents G0658 only Qty SetupSetup Safety Inventory Box Contents Figure QtyG0657 G0658 Clean UpG2544-Solvent Cleaner & Degreaser Site ConsiderationsMounting Setup To install the outboard turning attachment Model G0658 onlyTo prepare the lathe To test run the machine Test RunOperation Safety OperationsBasic Controls Tailstock Controls G0657/G0658 Benchtop Lathe To change speeds Changing Speed RangesAdjusting Tailstock Adjusting Tool Rest To position the tailstock along the bedTo position the tool rest base along the bed To install the live center Installing/Removing Spur CenterInstalling/Removing Live Center To install the spur centerTo remove the faceplate Removing/Installing FaceplateTo install the faceplate To remove the live centerGouge Selecting Turning ToolsTo place the tool rest on the outboard turning attachment Outboard Turning G0658 OnlySpindle Turning To set up a spindle turning operationTo mount your workpiece to the faceplate Faceplate TurningTo mount your workpiece to a backing block Sanding/FinishingG1082-4-Jaw Chuck AccessoriesG1194-3-Jaw Chuck H7828-Tool Table PlusUnpainted Cast Iron MaintenanceCleaning ScheduleTroubleshooting ServiceSymptom Possible Cause Possible Solution To install new belt Changing BeltTo remove the old belt Motor Service Motor control box wiring G0657/G0658 Wiring DiagramG0657 Main Breakdown Description G0657 Main Breakdown Parts ListG0657 Main Breakdown Parts List Contd G0657 Labels Breakdown & Parts List G0658 Main Breakdown G0658 Main Breakdown Parts List G0658 Main Breakdown Parts List contd G0658 Labels Breakdown & Parts List Page Page Warranty and Returns

G0657/G0658 specifications

The Grizzly G0657 and G0658 models are highly regarded in the woodworking community for their robust design and innovative features. These band saws provide woodworkers with the precision and performance required for a variety of cutting tasks.

One of the main features of the Grizzly G0657 is its 10-inch resaw capacity. This allows users to slice through thick materials with ease, making it an excellent choice for those who work with larger lumber or who need to resaw thick boards into thinner slabs. The G0658, on the other hand, offers an impressive 14-inch resaw capacity, ideal for larger projects requiring deep cuts.

Both models are equipped with a powerful 2 HP motor, which provides ample power to tackle tough cuts without bogging down, ensuring a smooth and efficient operation. The induction motor is designed to provide consistent power, crucial for achieving accurate and clean cuts. Additionally, the variable speed control on these saws allows users to adjust the speed according to the material they're cutting, adding to their versatility.

The construction of the G0657 and G0658 is another highlight. Built with a heavy-duty steel frame, both models exhibit exceptional stability and durability, reducing vibrations during operation. This stability enhances cutting accuracy, which is particularly beneficial when dealing with detailed or delicate woodworking projects.

Another significant characteristic of these band saws is their easy-to-adjust blade guides. Featuring micro-adjustable upper and lower blade guides, users can fine-tune their settings with minimal effort, ensuring optimal blade performance and longevity. The easy-access tensioning and tracking controls also simplify blade adjustments, allowing users to focus more on their projects and less on setup.

Safety features are integral to both the G0657 and G0658. They include a blade break and a clear blade guard for added visibility during operations. The built-in dust collection port helps maintain a cleaner workshop environment by minimizing debris, allowing for safer and more efficient work conditions.

In conclusion, the Grizzly G0657 and G0658 band saws combine power, precision, and user-friendly features, making them an excellent investment for both amateur and professional woodworkers. With their robust construction, adjustable settings, and effective safety measures, these models stand out in the woodworking tools market. Whether you’re reshaping lumber or crafting intricate designs, these band saws are designed to meet a variety of woodworking needs with reliability and ease.