Jet Tools JWL-1642EVS owner manual Sanding & Finishing, Face Plate & Bowl Turning, Mounting Stock

Page 16

Sanding & Finishing

Leaving clean cuts will reduce the amount of sanding required. Adjust lathe to a finishing speed, and begin with fine sandpaper (120 grit or finer). Coarser sandpaper will leave deep scratches that are difficult to remove, and dull crisp details. Fold the sandpaper into a pad; do not wrap sandpaper around your fingers or the workpiece.

To apply a finish, the workpiece can be left on the lathe. Turn off lathe and use a brush, or cloth to apply the finish. Remove excess finish before restarting lathe. Allow to dry and sand again with 320, or 400 grit sandpaper. Apply additional coats of finish and buff.

Face Plate & Bowl Turning

Face plate turning is normally done on the inboard side of the headstock over the bed, see Figure 20. You must move headstock to the end of the lathe bed for larger workpieces.

Mounting Stock

Use of a face plate is the most common method for holding a block of wood for turning bowls, and plates, see Figure 21.

1.Select stock at least 1/8" to 1/4" larger than the dimension on the desired finished workpiece.

2.True one surface of workpiece for mounting against the face plate. It is best to leave extra stock against the face plate that can be cut off when the workpiece is finished.

3.Using the face plate as a template, mark the location of the mounting holes, and drill pilot holes of the appropriate size. If the mounting screws on the face plate interfere with the workpiece, a waste block can be mounted to the face plate and then the waste block mounted to the workpiece by gluing or screwing, see Figure 21.

4.Both waste block and workpiece should have good flat surfaces.

5.Push in the spindle lock and thread face plate and workpiece onto spindle. Tighten set screws in face plate when secure.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents JWL-1642EVS Wood Lathe 708359 09/02Warranty & Service More Information WMH Tool Group WarrantyPage Diameter of Work Roughing RPM General Cutting Finishing RPM Grounding Instructions Volt OperationTable of Contents IntroductionSpecifications Input Power 115V OnlyUnpacking and Clean-Up Contents of the Shipping ContainersAssembly Stand Shelf Tool BasketGuard Controls & FeaturesHeadstock RPM Knob G, Fig Headstock Faceplate K, Fig Speed Change Disconnect the machine from the power sourceLathe Tools Mounting Workpiece Between Centers Stock Selection Roughing OutCoves CutsParting BeadsFace Plate & Bowl Turning Sanding & FinishingMounting Stock Face Plate or Chuck Wood SelectionChecks & Cracks DistortionTo Shape Outside of Bowl To Shape Interior of Bowl Sanding and FinsihingAdjusting Clamping Mechanism Changing the Belt and BearingsTroubleshooting Problem Possible Cause SolutionStand and Bed Assembly Index Part Description Size Qty Headstock Assembly JWL1642-MFC JWL1642-149 Wiring Diagram
Related manuals
Manual 32 pages 22.92 Kb

JWL-1642EVS specifications

The Jet Tools JWL-1642EVS and JWL-1642EVS-2 are standout lathes in the realm of woodturning, designed for both novice and seasoned woodworkers. These lathes offer unmatched versatility and precision, making them ideal for a wide variety of turning projects, from simple spindles to complex bowls.

One of the most notable features of the JWL-1642EVS is its powerful 1.5 HP motor that delivers excellent torque across a wide range of RPMs. This enhanced performance allows users to work with various wood species while maintaining smooth operation, a critical factor for achieving a high-quality finish. The electronic variable speed (EVS) control system provides convenient adjustments, allowing artisans to select the optimal speed for their specific turning needs. With a speed range from 40 to 3,600 RPM, craftspeople can effortlessly switch between fine detail work and aggressive stock removal.

The lathe's robust design is complemented by a cast iron bed that minimizes vibrations and ensures stability during operation. This construction not only enhances durability but also contributes to precise results, allowing users to create intricate designs without worrying about inconsistencies in the finish. Additionally, the JWL-1642EVS-2 variant offers an even larger capacity, with an impressive 16-inch swing over the bed and 42-inch length, accommodating larger workpieces.

Furthermore, both models feature a convenient electronic spindle lock, making the process of changing chucks and accessories quick and efficient. The adjustable swivel headstock allows for greater flexibility in accessing various angles, providing users with more control and comfort during operation.

Safety is also a priority in the design of the JWL-1642EVS and JWL-1642EVS-2, with features such as a safety restart switch, ensuring that the lathe cannot restart unexpectedly after a power interruption. Easy-to-read digital readouts for speed settings further enhance user experience by allowing for precise monitoring while turning.

Overall, the Jet Tools JWL-1642EVS and JWL-1642EVS-2 combine advanced technology, durable construction, and user-friendly features, making them indispensable tools for any woodturner looking to expand their craft and achieve professional-quality results. Whether you’re creating functional items or artistic pieces, these lathes empower users to elevate their woodturning endeavors.
Top Page Image Contents