Jet Tools J-7060 Adjustments, Starting the Saw, Coolant Flow, Coolant Mixture and Quantity

Page 11

rod. Position the stop post against the work piece and tighten the knob in the stop L-bracket. The stop post can be moved left or right as required to place the stop post against the work piece.

Starting the Saw

WARNING: NEVER OPERATE THE SAW WITH- OUT BLADE COVERS IN PLACE AND SECURED.

CAUTION: MAKE SURE THE BLADE IS NOT IN CONTACT WITH THE WORKPIECE WHEN THE MOTOR IS STARTED. DO NOT DROP THE SAW HEAD ON THE WORKPIECE OR FORCE THE SAW BLADE THROUGH THE WORKPIECE.

1.Raise the saw head.

2.Clamp the workpiece in the vise. (See figure 9 for examples of workpieces in the vise.)

3.Be sure to start the saw blade drive motor before allowing the blade to contact the workpiece.

4.Start the motor and allow the saw to come up to speed.

5.Slowly bring the saw down onto the workpiece. Adjust feed rate using feed rate control.

6.DO NOT LOWER THE SAW HEAD AT A RATE FASTER THAN THE SAW’S CAPABILITY OR FORCE THE CUT. Adjust the feed rate so the hydraulic cylinder provides the proper amount of downward force.

7.The saw will automatically shut off at the end of the cut.

Rounds

Flats/strips

Knock off sharp fedgef here with filef

ChannelsAngles

I-Beams

Squares/rectangles

Knock offf sharp edge heref with file

HexagonalsTees

Figure 9: Placing workpieces in the vise

Coolant Flow

CAUTION: THE COOLANT PUMP MUST BE SUB- MERGED BEFORE OPERATING TO PREVENT DAMAGE TO THE PUMP.

1.The blade guides are fitted with coolant fittings. Coolant is provided to the fittings through intercon- necting tubing. The coolant is dispensed directly onto the saw blade.

2.Adjust the coolant flow valves on the top, rear of the saw head as required to provide the desired flow. The flow should be no more than the blade can draw into the workpiece by movement of the blade.

3.The coolant flow can be stopped in two ways:

1)By using the coolant pump switch on the electrical equipment box, or

2)By closing the coolant flow valves on the top,

rear of the saw head.

Coolant Mixture and Quantity

The general purpose coolant is a mixture of water soluble oil and water. Mix one part of soluble oil (TRIM SOL) to ten parts of water (one quart oil, ten quarts of water). The eleven quarts of coolant is the amount required for the coolant pump to operate properly.

There are numerous coolants on the market that are formulated for special applications. Consult your local distributor for details in the event you have a long range production task, or are required to cut some of the more exotic materials.

Adjustments

The efficient operation of the cut-off saw is dependent upon the condition of the saw blade. If the performance of the saw begins to deteriorate, the first item that you should check is the blade.

If a new blade does not restore the machine’s cutting accuracy and quality, refer to the Trouble- shooting section (or the blade manufacturer’s guide) for conditions to consider and adjustments that can be made to increase the life of the blade.

To change the blade, refer to Changing Blades in the Maintenance section. To adjust the blade track- ing, refer to the following procedures.

Blade Tracking Adjustment

Blade tracking has been tested at the factory. Adjust- ment is rarely required when the blade is used properly or if the blade is correctly welded. (See figure 10 for location of blade tracking adjustment

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Inch x 20-Inch Semi Automatic Horizontal Cut-Off Band Saw Warranty and Service Table of Contents Specifications General SpecificationsWhen Setting up Machine Machinery General Safety WarningsGeneral Electrical Cautions Safety Instructions on Sawing SystemsControls IntroductionOperating Instructions Raising/Lowering the Saw Head Setting Blade SpeedOther Controls Blade Selection Blade Break-in ProceduresControlling the Cut Hydraulic Feed Control Evaluating Cutting EfficiencySecuring the Workpiece for Adjusting the Vise for Angle CutsInstallation and Adjustment of Work Stop Work Set-upCoolant Flow AdjustmentsBlade Tracking Adjustment Starting the SawExcessive Rubbing will Damage the Wheel AND/OR the Blade Factory or Field ProcedureTest Cutting to Verify Adjustment Accuracy Blade Guide Bearing AdjustmentLubrication MaintenanceAdjustment of Limit Switches CleaningReplacing the Drive Motor Servicing Hydraulic OilChanging Blades Changing the Drive BeltReplacing Idler Wheel or Idler Bearing Adjusting the Blade GuidesReplacement of Carbide Replacing the Drive WheelReplacing the Coolant Pump Replacement of GuideReplacement of Blade Edge Replacement of the Wire BrushElectrical Machine SetupUncrating and Spotting Wiring Diagram Fault Probable cause Suggested remedy TroubleshootingTroubleshooting Replacement Parts 55 56 Page Electrical Components Detail a Page WMH Tool Group

J-7060 specifications

Jet Tools J-7060 is a highly regarded model in the woodworking community, known for its reliability and precision. This bandsaw is designed to cater to both hobbyists and professional woodworkers, offering a robust platform for a variety of cutting tasks. Its powerful motor and thoughtful engineering make it stand out in a crowded market.

One of the primary features of the J-7060 is its heavy-duty construction. Built with a solid cast iron frame, this bandsaw provides exceptional stability during operation, reducing vibrations and allowing for cleaner cuts. The resilience of the materials used in its design ensures longevity, making it a worthwhile investment for those looking to enhance their workshop.

Powering this exceptional tool is a 1.5 HP motor, which delivers ample power for cutting through various materials, including hardwoods and softwoods with ease. The motor is equipped with a reliable dual voltage capability, allowing it to function efficiently in different voltage environments. This flexibility is especially beneficial for a range of workshop setups.

The J-7060 also incorporates advanced technology in its cutting mechanism. It features a 16-inch resaw capacity, enabling woodworkers to process materials up to 16 inches thick. This remarkable capacity is complemented by a blade tensioning system that allows for quick adjustments, ensuring optimal performance and precise cuts.

The Bandsaw's table is another highlight, as it comes with a large, extendable surface that provides ample workspace. This ensures that users can handle larger pieces of lumber effortlessly. The table is also made of cast iron, featuring precise tilting capabilities from 0 to 45 degrees, allowing for versatile cut angles suited for various projects.

Adding to the ease of use, the J-7060 is equipped with an integrated dust collection port that helps maintain a clean working environment. This feature not only makes cleanup simpler but also enhances visibility while cutting, contributing to overall safety during operation.

Ultimately, the Jet Tools J-7060 combines a powerful motor, heavy-duty construction, and user-friendly features, making it an exceptional choice for anyone aiming to elevate their woodworking experience. Whether tackling intricate projects or managing larger materials, this bandsaw is engineered to deliver performance and reliability over years of dedicated service. Its innovative design and practical functionalities make it a respected tool in the industry, perfect for both seasoned professionals and enthusiastic DIYers.
Top Page Image Contents