Jet Tools J-7060 operating instructions Machinery General Safety Warnings, When Setting up Machine

Page 5

-Misuse of this machine can cause serious injury.

-For safety, machine must be set up, used and serviced properly.

-Read, understand and follow instructions in the Operating Instructions and Parts Manual which was shipped with your machine.

When Setting up Machine:

-Always avoid using machine in damp or poorly lighted work areas.

-Always be sure the machine support is se- curely anchored to the floor or the work bench.

When Using Machine:

-Always wear safety glasses with side shields (See ANSI Z87.1)

-Never wear loose clothing or jewelry.

-Never overreach - you may slip and fall.

When Servicing Machine:

-Always disconnect the machine from its electri- cal supply while servicing.

- Always follow instructions in Operating Instruc- tions and Parts Manual when changing acces- sory tools or parts.

-Never modify the machine without consulting JET Corporation.

You - the Stationary Power Tool User - Hold the Key to Safety.

Read and follow these simple rules for best results and full benefits from your machine. Used properly, JET’s machinery is among the best in design and safety. However, any machine used improperly can be rendered inefficient and unsafe. It is absolutely mandatory that those who use our products be properly trained in how to use them correctly. They should read and understand the Operating Instruc- tions and Parts Manual as well as all labels affixed to the machine. Failure in following all of these warn- ings can cause serious injuries.

Machinery General Safety Warnings

1.Always wear protective eye wear when operating machinery. Eye wear shall be impact resistant, protective safety glasses with side shields which comply with ANSI Z87.1

specifications. Use of eye wear which does not comply with ANSI Z87.1specifications

could result in severe injury from breakage of eye protection.

2.Wear proper apparel. No loose clothing or jewelry which can get caught in moving parts. Rubber soled footwear is recommended for

best footing.

3.Do not overreach. Failure to maintain proper working position can cause you to fall into the machine or cause your clothing to get caught pulling you into the machine.

4.Keep guards in place and in proper working order. Do not operate the machine with guards

re moved.

5.Avoid dangerous working environments. Do not use stationary machine tools in wet or damp locations. Keep work areas clean and well lit.

6.Avoid accidental starts by being sure the start switch is OFF before plugging in the ma- chine.

7.Never leave the machine running while unat- tended. Machine shall be shut off whenever it is not in operation.

8.Disconnect electrical power before servicing.

Whenever changing accessories or general maintenance is done on the machine, electri- cal power to the machine must be discon-

nected before work is done.

9.Maintain all machine tools with care. Follow all maintenance instructions for lubricating and the changing of accessories. No attempt shall be made to modify or have makeshift repairs done to the machine. This not only voids the warranty but also renders the machine unsafe.

10.Machinery must be anchored to the floor.

11.Secure work. Use clamps or a vise to hold work, when practical. It is safer than using

your hands and it frees both hands to operate the machine.

12.Never brush away chips while the machine is inoperation.

13.Keep work area clean. Cluttered areas invite accidents.

14.Remove adjusting keys and wrenches before turning machine on.

15.Use the right tool. Don’t force a tool or attach- ment to do a job it was not designed for.

16.Use only recommended accessories and follow manufacturers instructions pertaining to them.

17.Keep hands in sight and clear of all moving parts and cutting surfaces.

18.All visitors should be kept at a safe distance

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Inch x 20-Inch Semi Automatic Horizontal Cut-Off Band Saw Warranty and Service Table of Contents Specifications General SpecificationsWhen Setting up Machine Machinery General Safety WarningsGeneral Electrical Cautions Safety Instructions on Sawing SystemsControls IntroductionOperating Instructions Raising/Lowering the Saw Head Setting Blade SpeedOther Controls Controlling the Cut Hydraulic Feed Control Blade Break-in ProceduresEvaluating Cutting Efficiency Blade SelectionInstallation and Adjustment of Work Stop Adjusting the Vise for Angle CutsWork Set-up Securing the Workpiece forBlade Tracking Adjustment AdjustmentsStarting the Saw Coolant FlowExcessive Rubbing will Damage the Wheel AND/OR the Blade Factory or Field ProcedureTest Cutting to Verify Adjustment Accuracy Blade Guide Bearing AdjustmentAdjustment of Limit Switches MaintenanceCleaning LubricationChanging Blades Servicing Hydraulic OilChanging the Drive Belt Replacing the Drive MotorReplacement of Carbide Adjusting the Blade GuidesReplacing the Drive Wheel Replacing Idler Wheel or Idler BearingReplacement of Blade Edge Replacement of GuideReplacement of the Wire Brush Replacing the Coolant PumpElectrical Machine SetupUncrating and Spotting Wiring Diagram Fault Probable cause Suggested remedy TroubleshootingTroubleshooting Replacement Parts 55 56 Page Electrical Components Detail a Page WMH Tool Group

J-7060 specifications

Jet Tools J-7060 is a highly regarded model in the woodworking community, known for its reliability and precision. This bandsaw is designed to cater to both hobbyists and professional woodworkers, offering a robust platform for a variety of cutting tasks. Its powerful motor and thoughtful engineering make it stand out in a crowded market.

One of the primary features of the J-7060 is its heavy-duty construction. Built with a solid cast iron frame, this bandsaw provides exceptional stability during operation, reducing vibrations and allowing for cleaner cuts. The resilience of the materials used in its design ensures longevity, making it a worthwhile investment for those looking to enhance their workshop.

Powering this exceptional tool is a 1.5 HP motor, which delivers ample power for cutting through various materials, including hardwoods and softwoods with ease. The motor is equipped with a reliable dual voltage capability, allowing it to function efficiently in different voltage environments. This flexibility is especially beneficial for a range of workshop setups.

The J-7060 also incorporates advanced technology in its cutting mechanism. It features a 16-inch resaw capacity, enabling woodworkers to process materials up to 16 inches thick. This remarkable capacity is complemented by a blade tensioning system that allows for quick adjustments, ensuring optimal performance and precise cuts.

The Bandsaw's table is another highlight, as it comes with a large, extendable surface that provides ample workspace. This ensures that users can handle larger pieces of lumber effortlessly. The table is also made of cast iron, featuring precise tilting capabilities from 0 to 45 degrees, allowing for versatile cut angles suited for various projects.

Adding to the ease of use, the J-7060 is equipped with an integrated dust collection port that helps maintain a clean working environment. This feature not only makes cleanup simpler but also enhances visibility while cutting, contributing to overall safety during operation.

Ultimately, the Jet Tools J-7060 combines a powerful motor, heavy-duty construction, and user-friendly features, making it an exceptional choice for anyone aiming to elevate their woodworking experience. Whether tackling intricate projects or managing larger materials, this bandsaw is engineered to deliver performance and reliability over years of dedicated service. Its innovative design and practical functionalities make it a respected tool in the industry, perfect for both seasoned professionals and enthusiastic DIYers.
Top Page Image Contents