Jet Tools J-7060 operating instructions Factory or Field Procedure

Page 12

12

Blade Tracking

Hex Adjustment

Screws

Single

Adjustment

Screw

Center

Locking

Screws

Figure 10: Blade tracking and tensioning

screws.)

Factory or Field Procedure

1.Raise the saw head enough to allow the saw motor to operate.

2.Loosen four knobs securing the blade cover. Lift the cover and swing it backward.

3.Remove the blade guard mounted on the left blade guide support.

4.Remove both blade guide bearing brackets. NOTE: Maintain proper tension at all times using the

blade tensioning mechanism.

5.Loosen the center locking screws in all three hex adjustment screws on the blade tensioning mechanism (see figure 10).

CAUTION: WHILE PERFORMING THE FOLLOW- ING, KEEP THE BLADE FROM RUBBING EXCES- SIVELY ON THE SHOULDER OF THE WHEEL.

EXCESSIVE RUBBING WILL DAMAGE THE WHEEL AND/OR THE BLADE.

6.Start the saw. Slowly turn the single hex adjust- ment screw at the rear of the tracking mechanism to tilt the idler wheel. Do not turn either of the

other two adjustment screws. Turn the adjustment screw until the blade is touching the shoulder of the idler wheel.

NOTE: Turning the screw inward causes the blade to move toward the shoulder of the wheel. Turning the screw outward causes the blade to move away from the shoulder.

7.Turn the single hex adjustment screw so the blade starts to move away from the shoulder of the wheel — then immediately turn the single hex adjustment screw in the other direction so the blade stops, then moves slowly toward the shoul- der.

WARNING: KEEP FINGERS CLEAR OF THE BLADE AND WHEEL TO AVOID INJURY.

8.Turn the single hex adjustment screw to stop the motion of the blade on the wheel as it gets closer to the wheel shoulder. Put a 6-inch length of paper between the blade and the wheel as shown in figure 11. The paper should not be cut as it passes between the wheel shoulder and the blade.

9.Turn the single hex adjustment screw a small amount. Repeat the insertion of the paper between the wheel shoulder and the blade until the paper is cut in two pieces.

NOTE: You may have to repeat the check with the paper several times before the blade and the shoulder cuts the paper into two pieces. Do not hurry the adjustment. Patience and accuracy here will pay off with better, more accurate, quieter cutting and much longer machine and blade life.

10.When the paper is cut, turn the hex adjustment screw slightly in the counterclockwise direction. This assures that the blade is not touching the shoulder of the wheel.

11.Shut off the saw.

12.Hold the hex adjustment screws with a wrench and tighten the center locking screws. Make sure the hex adjustment screws do not move while tightening the center screws.

13.Install the two blade guide bearing brackets. Position the guides so the bearings just touch the blade.

14.Install the left blade guard.

15.Close the saw head cover. Tighten the four knobs.

Motor "ON"

Upper Wheel

Rotating

Put Strip

Between

Wheel

and

Blade

Figure 11: Checking blade-to-wheel clearance using paper strips

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Inch x 20-Inch Semi Automatic Horizontal Cut-Off Band Saw Warranty and Service Table of Contents General Specifications SpecificationsMachinery General Safety Warnings When Setting up MachineSafety Instructions on Sawing Systems General Electrical CautionsIntroduction Operating InstructionsControls Setting Blade Speed Other ControlsRaising/Lowering the Saw Head Blade Break-in Procedures Controlling the Cut Hydraulic Feed ControlEvaluating Cutting Efficiency Blade SelectionAdjusting the Vise for Angle Cuts Installation and Adjustment of Work StopWork Set-up Securing the Workpiece forAdjustments Blade Tracking AdjustmentStarting the Saw Coolant FlowFactory or Field Procedure Excessive Rubbing will Damage the Wheel AND/OR the BladeBlade Guide Bearing Adjustment Test Cutting to Verify Adjustment AccuracyMaintenance Adjustment of Limit SwitchesCleaning LubricationServicing Hydraulic Oil Changing BladesChanging the Drive Belt Replacing the Drive MotorAdjusting the Blade Guides Replacement of CarbideReplacing the Drive Wheel Replacing Idler Wheel or Idler BearingReplacement of Guide Replacement of Blade EdgeReplacement of the Wire Brush Replacing the Coolant PumpMachine Setup Uncrating and SpottingElectrical Wiring Diagram Troubleshooting Fault Probable cause Suggested remedyTroubleshooting Replacement Parts 55 56 Page Electrical Components Detail a Page WMH Tool Group

J-7060 specifications

Jet Tools J-7060 is a highly regarded model in the woodworking community, known for its reliability and precision. This bandsaw is designed to cater to both hobbyists and professional woodworkers, offering a robust platform for a variety of cutting tasks. Its powerful motor and thoughtful engineering make it stand out in a crowded market.

One of the primary features of the J-7060 is its heavy-duty construction. Built with a solid cast iron frame, this bandsaw provides exceptional stability during operation, reducing vibrations and allowing for cleaner cuts. The resilience of the materials used in its design ensures longevity, making it a worthwhile investment for those looking to enhance their workshop.

Powering this exceptional tool is a 1.5 HP motor, which delivers ample power for cutting through various materials, including hardwoods and softwoods with ease. The motor is equipped with a reliable dual voltage capability, allowing it to function efficiently in different voltage environments. This flexibility is especially beneficial for a range of workshop setups.

The J-7060 also incorporates advanced technology in its cutting mechanism. It features a 16-inch resaw capacity, enabling woodworkers to process materials up to 16 inches thick. This remarkable capacity is complemented by a blade tensioning system that allows for quick adjustments, ensuring optimal performance and precise cuts.

The Bandsaw's table is another highlight, as it comes with a large, extendable surface that provides ample workspace. This ensures that users can handle larger pieces of lumber effortlessly. The table is also made of cast iron, featuring precise tilting capabilities from 0 to 45 degrees, allowing for versatile cut angles suited for various projects.

Adding to the ease of use, the J-7060 is equipped with an integrated dust collection port that helps maintain a clean working environment. This feature not only makes cleanup simpler but also enhances visibility while cutting, contributing to overall safety during operation.

Ultimately, the Jet Tools J-7060 combines a powerful motor, heavy-duty construction, and user-friendly features, making it an exceptional choice for anyone aiming to elevate their woodworking experience. Whether tackling intricate projects or managing larger materials, this bandsaw is engineered to deliver performance and reliability over years of dedicated service. Its innovative design and practical functionalities make it a respected tool in the industry, perfect for both seasoned professionals and enthusiastic DIYers.
Top Page Image Contents