Jet Tools 708358 specs

Warnings

1.Read and understand the entire owner’s manual before attempting assembly or operation.

2.This wood lathe is designed and intended for use by properly trained and experienced personnel only. If you are not familiar with the proper and safe operation of a wood lathe, do not use it until the proper training and knowledge have been obtained.

3.Always wear approved safety glasses/face shields while using this machine.

4.Make certain the machine is properly grounded.

5.Before operating the machine, remove tie, rings, watches, other jewelry, and roll sleeves up past the elbows. Remove all loose clothing and confine long hair. Do not wear gloves.

6.Keep the floor around the machine clean and free of scrap material, oil and grease.

7.Keep machine guards in place at all times when the machine is in use. If removed for maintenance purposes, use extreme caution and replace the guards immediately.

8.Do not over reach. Maintain a balanced stance at all times, so that you do not fall or lean against blades or other moving parts.

9.Make all machine adjustments or maintenance with the machine unplugged from the power source.

10.Use the right tool. Do not force a tool or attachment to do a job that it was not designed to do.

11.Replace warning labels if they become obscured or removed.

12.Make certain the switch is in the OFF position before connecting the machine to the power supply.

13.Give your work undivided attention. Looking around, carrying on a conversation and "horse-play" are careless acts that can result in serious injury.

14.Keep visitors a safe distance from the work area.

15.Use recommended accessories; improper accessories may be hazardous.

16.Read and understand warnings posted on the machine and in this manual. Failure to comply with all of these warnings may cause serious injury.

17.Some dust created by power sanding, sawing, grinding, drilling and other construction activities contain chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

•Lead from lead based paint.

•Crystalline silica from bricks, cement and other masonry products.

•Arsenic and chromium from chemically treated lumber.

Your risk of exposure varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety

equipment, such as face or dust masks that are specifically designed to filter out microscopic particles

18.Do not operate this lathe while under the influence of drugs, alcohol or any medication.

19.Keep tools sharp and clean for safe and best performance. Dull tools can grab in the work and be jerked from the operator`s hands causing serious injury.

20.Check the condition of the stock to be turned. Make sure it is free of knots, warpage, checked ends, improperly made or cured glue joints and other conditions which can cause it to be thrown out of the lathe.

21.Securely fasten spur/live centers to the material being used.

22.Check centers and center sockets in the headstock and tailstock to be sure they are free of dirt or rust and oil lightly before inserting centers.

23.Test each set-up by revolving the work by hand to insure it clears the tool rest and bed. Check the setup at the lowest speed before increasing it to the operating speed.

24.Use the correct cutting tool for the operation to be performed and keep all tools sharp.

25.Use low speeds for roughing and for long or large diameter work. If vibration occurs, stop the machine and correct the cause. See the speed recommendation chart on the next page.

708358 specifications

The Jet Tools 708358 is a powerful and reliable 15-Inch Planer, designed for both professional woodworkers and serious DIY enthusiasts. This robust machine combines advanced features with efficient performance, making it a valuable addition to any workshop.

One of the key highlights of the Jet 708358 is its powerful 3 HP motor, which operates at a 230V power supply. This motor provides the necessary torque to handle dense hardwoods and ensures consistent performance across a variety of applications. The combination of this motor and high-quality components makes it an excellent choice for those looking to achieve precision and speed in their woodworking tasks.

The Jet 708358 features a massive 15-inch cutting width, allowing users to tackle larger workpieces with ease. Its precise depth adjustment mechanism enables users to set the depth of cut from 1/16 inch up to a maximum of 1/8 inch. This feature is particularly useful when working with materials of different thicknesses, ensuring versatile operation without sacrificing accuracy.

Another notable technology integrated into the Jet 708358 is its helical cutter head. Unlike traditional straight blades, the helical design features multiple, staggered cutting edges that significantly reduce noise and provide a smoother finish on the workpiece. This cutter head also increases the lifespan of the knives, requiring less frequent replacements and maintenance.

The built-in dust collection system is another standout characteristic, featuring a 4-inch port that effectively removes wood shavings and debris from the work area. This not only keeps the workspace clean but also enhances visibility and safety during operation.

Additionally, the Jet 708358 is equipped with a user-friendly control panel, featuring easy-to-read depth adjustment levers and a convenient on/off switch. The sturdy, cast-iron frame ensures stability and reduces vibration, contributing to the accuracy and quality of every cut.

Overall, the Jet Tools 708358 offers a combination of power, technology, and features that make it a top choice for woodworkers seeking reliable and high-quality performance in their planing tasks. With its exceptional cutting capabilities and user-oriented design, it stands as a trusted workhorse in any woodworking environment.