DeWalt DW708 manual Polarized Plugs, Important Safety Instructions, Ampere Rating, Awg

Page 6

English

Important Safety Instructions for all tools.

WARNING: For your own safety read instruction manual before operating sliding compound miter saw.

WARNING: When using electric tools, basic safety precautions should always be followed to reduce risk of fire, electric shock, and personal injury, including the following:

Double Insulation

Double insulated tools are constructed throughout with two separate layers of electrical insulation or one double thickness of insulation between you and the tool’s electrical system. Tools built with this insulation system are not intended to be grounded. As a result, your tool is equipped with a two prong plug which permits you to use extension cords without concern for maintaining a ground connection.

NOTE: Double insulation does not take the place of normal safety precautions when operating this tool. The insulation system is for added protection against injury resulting from a possible electrical insulation failure within the tool.

CAUTION: WHEN SERVICING USE ONLY IDENTICAL REPLACEMENT PARTS. Repair or replace damaged cords.

Polarized Plugs

To reduce the risk of electric shock, this equipment has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way.

Important Safety Instructions

KEEP GUARDS IN PLACE and in working order.

REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on.

KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries.

DON’T USE IN DANGEROUS ENVIRONMENT. Don’t use power tools in damp or wet locations, or expose them to rain or snow. Keep work area well lighted.

KEEP CHILDREN AWAY. All visitors should be kept safe distance from work area.

MAKE WORKSHOP KID PROOF with padlocks, master switches, or by removing starter keys.

DON’T FORCE TOOL. It will do the job better and safer at the rate for which it was designed.

USE RIGHT TOOL. Don’t force tool or attachment to do a job for which it was not designed.

USE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. The following table shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage number, the heavier the cord.

 

 

 

Minimum Gage for Cord Sets

 

Volts

 

 

Total Length of Cord in Feet

120V

 

 

0-25

26-50

51-100

101-150

240V

 

 

0-50

51-100

101-200

201-300

Ampere Rating

 

AWG

 

More

 

Not more

 

 

Than

 

Than

 

 

 

 

0

-

6

18

16

16

14

6

-

10

18

16

14

12

10

-

12

16

16

14

12

12

-

16

14

12

Not Recommended

WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry which may get caught in moving parts. Nonslip footwear is recommended. Wear protective hair covering to contain long hair.

ALWAYS USE SAFETY GLASSES. Also use face or dust mask if cutting operation is dusty. Everyday eyeglasses only have impact resistant lenses, they are not safety glasses.

SECURE WORK. Use clamps or vise when you cannot secure the workpiece on the table and against the fence by hand or when your hand will be dangerously close to the blade (within 6”)

DON’T OVERREACH. Keep proper footing and balance at all times.

MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories.

DISCONNECT TOOLS before servicing; when changing accessories, such as blades, clamps, extensions, and the like.

REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure switch is in off position before plugging in.

USE RECOMMENDED ACCESSORIES. Consult the instruction manual for recommended accessories. The use of improper accessories may cause risk of injury to persons.

NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or if the cutting tool is unintentionally contacted.

CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function–check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced.

NEVER LEAVE TOOL RUNNING UNATTENDED. TURN POWER OFF. Don’t leave tool until it comes to a complete stop.

REPLACEMENT PARTS. When servicing, use only identical replacement parts.

Additional Safety Rules for Sliding Compound Miter Saw

Wear eye protection.

Keep hands out of path of saw blade. NEVER CUT A PIECE WHERE HAND WOULD BE 6" (152 mm) OR LESS FROM BLADE.

Do not operate saw without guards in place.

Do not perform any operation freehand.

Never reach in back of saw blade.

Turn off tool and wait for saw blade to stop before moving workpiece or changing settings.

Disconnect power before changing blade or servicing.

Blade adjustment is to be made only with the power off and the blade stopped.

Never use saw without kerf plate.

Replace kerf plate when worn.

To reduce risk of injury, return carriage to the full rear position after each crosscut operation.

CAUTION: FAILURE TO HEED THESE WARNINGS MAY RESULT IN PERSONAL INJURY AND SERIOUS DAMAGE TO THE SAW.

DO-Protect electric supply line with at least a 15 ampere time-delay fuse or a circuit breaker.

DO-Make certain the blade rotates in the correct direction and that the teeth at the bottom of the blade are pointing to the rear of the sliding compound miter saw.

DO use stabilizer bar at all times.

DO-Be sure all clamp handles and knobs are tight before starting any operation.

DO-Be sure all blade and clamp washers are clean and recessed sides of collars are against blade. Tighten arbor screw securely.

DO- Keep saw blade sharp and properly aligned.

DO-Keep motor air slots free of chips and dirt.

DO-Use blade guards at all times.

2

Image 6
Contents Page DW708 Copyright Dewalt DEWALT… Built Jobsite Tough Table of Contents Polarized Plugs Important Safety InstructionsAdditional Safety Rules for Sliding Compound Miter Saw Ampere RatingOn Base On Stabilizer Unpacking Your Saw SpecificationsElectrical Connection FamiliarizationOptional Attachments/Accessories Capacity of CUTDrive Transporting the Saw StabilizerBench Mounting Lock Down PIN Screw Back of SAW StabilizerscrewMiter Pointer Adjustment AdjustmentsMiter Scale Adjustment Miter LOCK/DETENT ROD AdjustmentTurn Off and Unplug the Miter Saw Adjusting the bevel stop to 45 left or rightFence Adjustment Guard Actuation and VisibilityBrushes OperationSupport for Long Pieces Clamping the WorkpieceTurn Off and Unplug Saw Correct IncorrectVernier Scale When Mitering to the RightWhen Mitering to the Left Dual Range Miter ScaleInside Corner Outside Corner Cutting Crown MoldingSAW SettingDegree Miter Bevel Degree Setting SET this Bevel Angle on SAWRemoving and Replacing Belt Installing a New Saw BladeSpecial Cuts GroovingMaintenance Full WarrantyDAY no Risk Satisfaction Guarantee Trouble Shooting Guide Be Sure to Follow Safety Rules and InstructionsWHAT’S WRONG? What to DO…
Related manuals
Manual 54 pages 16.49 Kb