Delta TS200, ts200ls instruction manual Maintenance, Service, Accessories, Warranty

Page 25

MAINTENANCE

KEEP MACHINE CLEAN

Periodically blow out all air passages with dry compressed air. All plastic parts should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material.

Wear ANSI Z87.1 safety glasses while using compressed air.

FAILURE TO START

Should your machine fail to start, check to make sure the prongs on the cord plug are making good contact in the outlet. Also, check for blown fuses or open circuit breakers in the line.

LUBRICATION

Apply household floor paste wax to the machine table and extension table or other work surface weekly.

PROTECTING CAST IRON FROM RUST

To clean and protect cast iron tables from rust, you will need the following materials: 1 pushblock from a jointer, 1 sheet of medium Scotch-Brite™ Blending Hand Pad, 1 can of WD-40®, 1 can of degreaser, 1 can of TopCote® Aerosol. Apply the WD-40 and polish the table surface with the Scotch-Brite pad using the pushblock as a holddown. Degrease the table, then apply the TopCote® accordingly.

SERVICE

PARTS, SERVICE OR WARRANTY ASSISTANCE

All Delta Machines and accessories are manufactured to high quality standards and are serviced by a network of Porter-Cable Delta Factory Service Centers and Delta Authorized Service Stations. To obtain additional information regarding your Delta quality product or to obtain parts, service, warranty assistance, or the location of the nearest service outlet, please call 1-800-223-7278 (In Canada call 1-800-463-3582).

ACCESSORIES

A complete line of accessories is available from your Delta Supplier, Porter-Cable • Delta Factory Service Centers, and Delta Authorized Service Stations. Please visit our Web Site www.deltamachinery.com for a catalog or

for the name of your nearest supplier.

Since accessories other than those offered by Delta have not been tested with this product, use of such accessories could be hazardous. For safest operation, only Delta recommended accessories should be used with this product.

WARRANTY

Two Year Limited New Product Warranty

Delta will repair or replace, at its expense and at its option, any new Delta machine, machine part, or machine accessory which in normal use has proven to be defective in workmanship or material, provided that the customer returns the product prepaid to a Delta factory service center or authorized service station with proof of purchase of the product within two years and provides Delta with reasonable opportunity to verify the alleged defect by inspection. For all refurbished Delta product, the warranty period is 180 days. Delta may require that electric motors be returned prepaid to a motor manufacturer’s authorized station for inspection and repair or replacement. Delta will not be responsible for any asserted defect which has resulted from normal wear, misuse, abuse or repair or alteration made or specifically authorized by anyone other than an authorized Delta service facility or representative. Under no circumstances will Delta be liable for incidental or consequential damages resulting from defective products. This warranty is Delta’s sole warranty and sets forth the customer’s exclusive remedy, with respect to defective products; all other warranties, express or implied, whether of merchantability, fitness for purpose, or otherwise, are expressly disclaimed by Delta.

25

Image 25
Contents Motorized Bench Saw Important Safety Instructions Table of ContentsCalifornia Proposition Safety Guidelines DefinitionsImportant Safety Instructions General Safety RulesStay ALERT, Watch What YOU are DOING, USE of this Tool can GenerateFailure to Follow These Rules MAY Result in Serious Injury Additional Specific Safety RulesMotor Specifications Power ConnectionsGrounding Instructions Functional Description Carton ContentsParts Unpacking and Cleaning AssemblyAssembly Tools Required Elevating and Supporting Surfaces for a SAW with no StandSAW to Stand TS200LS only Assembling Stand for Model TS200LSAttaching Blade Guard and Splitter Assembly Attaching Blade Height Adjusting HandwheelOn the screw L Fig Attaching Miter Gauge Holder Miter GaugeIllustrates the miter gauge D inserted into the holder Assembling RIP FenceBlade Height Adjustment Locking Switch in the OFF PositionOperation Starting and Stopping SAW45 Degree Positive Stop Adjustments Blade Tilt AdjustmentTo Adjust Positive Stop AT 45 Degrees Table Insert Adjustment RIP Fence Operation AdjustmentsAdjusting Blade Parallel to Miter Gauge Slots Miter Gauge Operation AdjustmentsCROSS-CUTTING Changing the BladeRipping Never USE the Fence AS a CUT-OFF Gage When CROSS-CUTTINGAccessory Dado Cutterhead Using Auxiliary Wood Facing on RIP FenceConstructing a Push Stick Guard Removed for CLARITY. Always USE the GuardPage Constructing a Push Stick PushstickPower Tool Institute TroubleshootingConstructing a Featherboard Service MaintenanceAccessories WarrantyPage Canadian PORTER-CABLE Delta Service Centers