Delta 36-841 instruction manual Power Connections, Motor Specifications, Grounding Instructions

Page 4

POWER CONNECTIONS

A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which have 3- prong grounding type plugs and matching receptacle which will accept the machine’s plug. Before connecting the motor to the power line, make sure the switch is in the “OFF” position and be sure that the electric current is of the same characteristics as indicated on the machine. All line connections should make good contact. Running on low voltage will damage the motor.

WARNING: DO NOT EXPOSE THE MACHINE TO RAIN OR OPERATE THE MACHINE IN DAMP LOCATIONS.

MOTOR SPECIFICATIONS

Your machine is wired for 230 volt, 60 HZ alternating current. Before connecting the machine to the power source, make sure the switch is in the “OFF” position.

GROUNDING INSTRUCTIONS

WARNING: THIS MACHINE MUST BE GROUNDED WHILE IN USE TO PROTECT THE OPERATOR FROM ELECTRIC SHOCK.

1. All grounded, cord-connected machines:

In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This machine is equipped with an electric cord having an equipment- grounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances.

Do not modify the plug provided - if it will not fit the outlet, have the proper outlet installed by a qualified electrician.

Improper connection of the equipment-grounding conductor can result in risk of electric shock. The conductor with insulation having an outer surface that is green with or without yellow stripes is the equipment- grounding conductor. If repair or replacement of the electric cord or plug is necessary, do not connect the equipment-grounding conductor to a live terminal.

Check with a qualified electrician or service personnel if the grounding instructions are not completely understood,

or if in doubt as to whether the machine is properly grounded.

Use only 3-wire extension cords that have 3-prong grounding type plugs and matching 3-conductor receptacles that accept the machine’s plug, as shown in Fig. C.

Repair or replace damaged or worn cord immediately.

2.Grounded, cord-connected machines intended for use on a supply circuit having a nominal rating between

150- 250 volts, inclusive:

This machine is intended for use on a circuit that has an outlet that looks like the one illustrated in Fig. C. The machine has a grounding plug that looks like the plug illustrated in Fig. C. Make sure the machine is connected to an outlet having the same configuration as the plug. No adapter is available or should be used with this machine. If the machine must be reconnected for use on a different type of electric circuit, the reconnection should be made by qualified service personnel; and after reconnection, the machine should comply with all local codes and ordinances.

WARNING: IN ALL CASES, MAKE SURE THE RECEPTACLE IN QUESTION IS PROPERLY

GROUNDED. IF YOU ARE NOT SURE HAVE A QUALIFIED ELECTRICIAN CHECK THE RECEPTACLE. NEVER REMOVE GROUNDING PRONG FROM POWER PLUG.

NOTE: In Canada, the use of a temporary adapter is not permitted by the Canadian Electric Code.

GROUNDED OUTLET BOX

CURRENT CARRYING

PRONGS

240 VOLT

GROUND

PRONG

Fig. C

4

Image 4
Contents Limited Edition Unisaw with 52 Unifence General Safety Rules Additional Safety Rules for Circular Saws Refer to them often Use them to instruct othersMotor Specifications Power ConnectionsGrounding Instructions Unpacking and Cleaning Extension CordsUnisaw Unifence Commercial Biesemeyer Fence System Assembling Blade Tilting Mechanism HandleAssembling ON/OFF Switch Assembling Extension WingsAssembling Blade Guard and Splitter Assembly Using a wrench to hold the hex nut J , tight Fastening Motor Cord to SAW Frame Motor Cover Miter Gage Holder and Wrench HolderAssembling RIP Fence Holder Brackets Assembling Dust Chute AdapterPage Page Assembling Unifence Shelf Board Assembling Unifence Guide Rail to TablePage Setting Flip Stop Assembling Unifence Rail StopAssembling Cursor to Unifence Body Adjusting Clamp Handle Positive IndentsAssembling Unifence Body to Guide Rail Assembling Fence to Unifence Body Fence OperationRipping with Unifence Adjusting Fence 90 Degrees to Table Adjusting Fence Parallel to Miter Gage SlotsAdjusting Clamping Action of Fence Locking Handle Ripping on Left Side of SAW BladeUsing the Fence AS a CUT-OFF Gage Using Auxiliary Wood Facing on the UnifenceAssembling Guide Rails Assembling Table Legs to Extension Table Assembling Guide Tube to Front Rail Adjusting Clamping Action of Fence Locking Handle Adjusting Fence Parallel to Miter Gage SlotsFence Lubrication Operating Controls Unisaw Adjustments Starting and Stopping the SAWAdjusting 90 and 45 Degree Positive Stops Adjusting TableAdjusting Table Insert Miter Gage Operation and AdjustmentReplacing Belts and Adjusting Belt Tension MaintenanceChanging the SAW Blade Protecting Cast Iron Table from Rust OperationsCROSS-CUTTING Using Auxiliary Wood Facing on Biesemeyer RIP Fence RippingUsing Accessory Moulding Cutterhead Using Accessory Dado Head Blade Guard Accessories Constructing a FeatherboardPushstick Constructing a Push StickAccessories PARTS, Service or Warranty Assistance Canadian PORTER-CABLE Delta Service Centers