Black & Decker 90510288 manual Features, Assembly, Use

Page 5

130oC The charger automatically shuts off if the ambient temperature becomes too high. As a consequence the charger will be inoperable. The charging base must be disconnected from the mains supply and taken to an authorised service centre for repair.

The charging base is intended for indoor use only.

This appliance is not intended for use by young or infirm persons without supervision. Children must be supervised to ensure they do not play with the appliance.

If the supply cord is damaged, it must be replaced by the manufacturer or an authorised Black & Decker Service Centre in order to avoid a hazard.

Features

1.Shoe

2.Lock-off button

3.Charging socket

4.On/Off switch

5.Blade clamp release lever

6.Charger plug

7.Charger

battery will attain full capacity. The battery may become warm while charging; this is normal and does not indicate a problem.

Warning! Do not charge the battery at ambient temperatures below 4 °C or above 40 °C. Recommended charging temperature is approximately 24 °C.

To charge the battery, insert the charger plug (6) into the charging socket (3).

Plug in the charger (7) and switch on at the mains. Leave the tool connected to the charger for 6-8 hours. The charger may hum and become warm while charging; this is normal and does not indicate a problem.

Generally, a charging time of 6 hours will enable the tool to operate at an effective power level for most tasks. However, further charging for up to 8 hours could significantly increase the run time, depending on the battery and the charging conditions.

Before using the tool, unplug the charger (7) and disconnect the tool from the charger.

Do not use the tool while it is connected to the charger.

Switching on and off (fig. C)

To switch the tool on, push the lock-off button (2) to the unlock position and squeeze the on/off switch (4).

To switch the tool off, release the on/off switch (2).

Assembly

Fitting and removing a saw blade (fig. A)

The tool accepts both T-shank and universal shank jig saw blades.

Fitting:

Push down on the blade clamp release lever (5) to its fully open position.

Insert the blade shank (8) from the front. Release the blade clamp release lever (5).

Removing:

Push down on the blade clamp release lever (5) to its fully open position.

Remove the blade.

Release the blade clamp release lever (5).

Use

Warning! Let the tool work at its own pace. Do not overload.

Charging the battery (fig. B)

The battery needs to be charged before first use and whenever it fails to produce sufficient power on jobs that were easily done before. When charging the battery for the first time, or after prolonged storage, it will only accept an 80% charge. After several charge and discharge cycles, the

Sawing (fig. D)

Hold the tool firmly with both hands while cutting.

The shoe (1) should be held firmly against the material being cut. This will help to prevent the saw from jumping, reduce vibration and minimise blade breakage.

Let the blade run freely for a few seconds before starting the cut.

Apply only a gentle pressure to the tool while performing the cut.

Hints for optimum use

Sawing laminates

Because the saw blade cuts on the upward stroke, splintering may occur on the surface closest to the shoe plate.

Use a fine-tooth saw blade.

Saw from the back surface of the workpiece.

To minimise splintering, clamp a piece of scrap wood or hardboard to both sides of the workpiece and saw through this sandwich.

Sawing Metal

Be aware that sawing metal takes much more time than sawing wood.

Use a saw blade suitable for sawing metal.

5

Image 5
Contents Ireland Australia New Zealand Page Personal safety Electrical safetyPower tool use and care Intended useService Battery tool use and careSpecific safety instructions for Saws Symbols on the ChargerUse FeaturesAssembly Technical data CHS6000 MaintenanceProtecting the environment EC declaration of conformityGuarantee CHS6000 Page Page Page 10/06