Carrier 90MA/MF/MU manual Unit Dimensions

Page 11

UNIT

 

004

 

006

 

008,012

 

 

 

A

 

36.19(919)

 

48(1219)

B

 

21.88(556)

 

29.62(752)

C

 

59.12(1501)

 

69.50(1765)

D

 

 

 

SEE NOTE 2

 

 

E

 

 

24(610)

 

 

 

 

 

 

 

 

F

 

13.81(351)

 

16.44(418)

 

19.38(492)

G

 

13.13(333)

 

15(381)

 

17.25(438)

H

 

0.75(19)

 

0.75(19)

 

1.31(33)

J

 

12.5(318)

 

10.62(270)

 

11.44(291)

K

 

17.06(433)

 

23.25(591)

L

 

20.50(521)

 

25.37(644)

M

 

17(432)

 

17(432)

N

 

31.88(810)

 

42.62(1083)

P

 

2.06(52)

 

3(76)

Q

 

10(254)

 

12.50(318)

R

 

15.56(395)

 

16(406)

NOTES:

1.Certified dimension drawings available upon request

2.Minimum required clearance at back of unit is zero. Clearance above and at right (90MA008,012 only) and at left of

unit depends on space required for accessory plenum, ductwork, condenser piping, accessory heater piping, condensate drain line and power wiring

3.Water connections are located on left side of unit (Refer to “Make Condenser Connections”, Condensate drain connections are located on left side of unit for 004 & 006, and on both sides of unit for 008 & 012.

Figure 2 Unit Dimensions

b.Attach a one-inch (2.5 cm) flange or attach a flanged, flexible duct connection directly to unit.

If an outdoor makeup air damper is to be installed, at- tach it directly to unit back panel and install flexible connection between damper and remaining duct- work. Use accepted ductwork installation proce- dures. Follow all applicable codes.

c.Completely blank off the standard return-air opening with a field-fabricated filler panel. The panel must be removable for service access. Refer to paragraph 5.1.

3.9Check Return--Air Filters

Ensure filters shipped with unit are in place. Never operate unit without return air filters in place.

3.10Align Fan Shaft and Wheel

HORIZONTAL WHEEL CENTERING --All wheels must be

horizontally centered between the inside edges of their fan scroll ventures (Figure 3). Adjust as follows:

a. Loosen set screws holding wheel to shaft. b. Center the wheel by sliding it horizontally. c. Re-tighten set screws.

CONCENTRIC ALIGNMENT --Shaft and wheels must be concentrically centered with the venturi (Figure 4). Shaft bearings are supported by bearing supports. If shaft and wheels are concentrically misaligned from shipping shock, it is possible to re-bend bearing support arms to original positions. Replace the bearing support if it has been extensively damaged during shipping.

DIMENSION “D” MUST BE EQUAL ALL AROUND

 

Figure 3 Horizontal Wheel Centering

Figure 4 Concentric Wheel Alignment

5

62--10458--00

Image 11
Contents Installation Operation & Service Models Safety Summary 62--10458--00 Safety-2 Table of Contents List of Illustrations Introduction Base Unit 90MA/MF/MU Units 404 406 408 Base Unit 90MA/MF Units Unit Dimensions Install water-regulating valve in water supply line Unit Length of RUN Operation Service Condensers may require cleaning of water-deposited scale Forced Circulation Method Refrigerant Charging 134a Units Mounting Wiring Schematic -- 90MA/MF/MU004/006 Component Arrangement -- 90MA/MF/MU004/006 62--10458--00 Wiring Schematic -- 90MA/MF/MU008/012 Component Arrangement -- 90MA/MF/MU008/012 62--10458--00 Index 62--10458--00

90MA/MF/MU specifications

The Carrier 90MA/MF/MU series represents a significant advancement in HVAC technology, designed for commercial applications needing reliability, efficiency, and precision in climate control. These units are renowned for their ability to cater to varying thermal loads while minimizing energy consumption, making them an ideal choice for various settings including offices, retail spaces, and industrial facilities.

One of the standout features of the Carrier 90MA/MF/MU series is its impressive energy efficiency. The equipment is designed with advanced thermodynamic principles to ensure maximum heat transfer and minimal energy loss. With high Seasonal Energy Efficiency Ratios (SEER) and Energy Efficiency Ratios (EER), these units help building owners achieve higher energy savings compared to traditional HVAC systems.

Another significant characteristic of the 90MA/MF/MU series is the integration of advanced control technologies. The units come equipped with sophisticated microprocessor-based controls that allow for precise temperature management and enhance overall system performance. Features like modulating capabilities and variable speed fans provide superior comfort levels by continuously adjusting to the changing environmental conditions.

The 90MA series also emphasizes quiet operation, which is critical for commercial environments. The innovative design includes insulation and vibration dampening technologies that reduce noise levels, ensuring a comfortable working atmosphere.

Durability and reliability are also central to the design of the Carrier 90MA/MF/MU series. These units are engineered with high-quality materials and components, including robust compressors and corrosion-resistant finishes that withstand harsh weather conditions. This durability extends the lifespan of the units, thus reducing maintenance costs and downtime.

In terms of versatility, the 90MA/MF/MU series offers a broad range of configurations and options, including various sizes and capacities. This flexibility allows for tailored solutions that meet the specific needs of different applications, from large commercial buildings to smaller retail outlets.

The series also supports environmentally friendly refrigerants that comply with global standards, marking Carrier’s commitment to sustainable practices. This approach not only reduces environmental impact but also positions businesses favorably in the eyes of eco-conscious consumers.

Overall, the Carrier 90MA/MF/MU series stands out as a pinnacle of efficiency, performance, and reliability in the commercial HVAC market. Its advanced technologies and thoughtful design cater to the diverse needs of modern businesses while promoting a sustainable and comfortable indoor environment.