Carrier 90MA/MF/MU manual Install water-regulating valve in water supply line

Page 12

90MA/MF004/006 UNITS

90MA/MU008/012 UNITS

90MU004/006 UNITS

90MU008/012 UNITS

 

UNIT

A*

B*

C*

D*

E

F

G

90MA/MF004

1/2

1/2

----

¾ FPT

----

----

1.75

 

 

 

 

 

 

 

(45)

90MA/MF006

3/4

----

3/4

 

----

----

90MA/MF008/012

1”

1”

----

 

----

----

 

90MU004

----

----

----

 

1/2 flare

1/2 flare

 

90MU006

----

----

----

 

1/2 flare

1/2 flare

 

90MU008/012

----

----

----

 

5/8 O.D.

3/4 O.D.

 

*A = Condenser In, B & C = Condenser Out, D = Condensate, all Female Pipe Thread, E = Liquid Refrigerant (field cut), F = Refrigerant Discharge (field cut), G = Electrical Opening

Figure 5 Connection Locations

3.11 Check Compressor Spring Mounts

Install water-regulating valve in water supply line

(008 & 012 size only)

outside cabinet as follows.

The compressors are held rigid in shipment by bolts extending through a washer, grommet and compressor foot into a weld nut. Loosen each bolt (4 per compressor) until compressor floats freely on springs. Then re-tighten bolts until there is slight pressure on the neoprene gasket. This will steady the compressor and prevent start and stop rocking.

The compressors have reversible oil pumps that operate in either direction; therefore, the direction of rotation need not be checked.

3.12Make Condenser Connections

UNIT MOUNTED CONDENSER (90MA/MF) - Condenser

water inlet and outlet connections are shown in Figure 5. Piping arrangements for condenser cooling water are shown in Figure 6.

Connect condenser water supply and return lines as indicated. When connecting water lines, hold the condenser inlet and outlet stubs firmly with a wrench at the female pipe thread hex fitting to prevent twisting. Do not use water lines smaller than connection sizes shown in Figure 5. Observe all applicable plumbing and sanitary codes.

See Figure 5

Figure 6 Typical Condenser Water Piping

a. Route regulating valve capillary with its flare nut to the port on refrigerant discharge line (Figure 1), us- ing any convenient unused opening on side of unit. Use a grommet in panel to prevent chafing of capil- lary.

b. Remove cap from discharge line fitting.

c.Remove cotter pin taped to discharge line fitting. In- sert pin, split end first, into regulating valve flare.

62--10458--00

6

 

Image 12
Contents Installation Operation & Service Models Safety Summary 62--10458--00 Safety-2 Table of Contents List of Illustrations Introduction Base Unit 90MA/MF/MU Units 404 406 408 Base Unit 90MA/MF Units Unit Dimensions Install water-regulating valve in water supply line Unit Length of RUN Operation Service Condensers may require cleaning of water-deposited scale Forced Circulation Method Refrigerant Charging 134a Units Mounting Wiring Schematic -- 90MA/MF/MU004/006 Component Arrangement -- 90MA/MF/MU004/006 62--10458--00 Wiring Schematic -- 90MA/MF/MU008/012 Component Arrangement -- 90MA/MF/MU008/012 62--10458--00 Index 62--10458--00

90MA/MF/MU specifications

The Carrier 90MA/MF/MU series represents a significant advancement in HVAC technology, designed for commercial applications needing reliability, efficiency, and precision in climate control. These units are renowned for their ability to cater to varying thermal loads while minimizing energy consumption, making them an ideal choice for various settings including offices, retail spaces, and industrial facilities.

One of the standout features of the Carrier 90MA/MF/MU series is its impressive energy efficiency. The equipment is designed with advanced thermodynamic principles to ensure maximum heat transfer and minimal energy loss. With high Seasonal Energy Efficiency Ratios (SEER) and Energy Efficiency Ratios (EER), these units help building owners achieve higher energy savings compared to traditional HVAC systems.

Another significant characteristic of the 90MA/MF/MU series is the integration of advanced control technologies. The units come equipped with sophisticated microprocessor-based controls that allow for precise temperature management and enhance overall system performance. Features like modulating capabilities and variable speed fans provide superior comfort levels by continuously adjusting to the changing environmental conditions.

The 90MA series also emphasizes quiet operation, which is critical for commercial environments. The innovative design includes insulation and vibration dampening technologies that reduce noise levels, ensuring a comfortable working atmosphere.

Durability and reliability are also central to the design of the Carrier 90MA/MF/MU series. These units are engineered with high-quality materials and components, including robust compressors and corrosion-resistant finishes that withstand harsh weather conditions. This durability extends the lifespan of the units, thus reducing maintenance costs and downtime.

In terms of versatility, the 90MA/MF/MU series offers a broad range of configurations and options, including various sizes and capacities. This flexibility allows for tailored solutions that meet the specific needs of different applications, from large commercial buildings to smaller retail outlets.

The series also supports environmentally friendly refrigerants that comply with global standards, marking Carrier’s commitment to sustainable practices. This approach not only reduces environmental impact but also positions businesses favorably in the eyes of eco-conscious consumers.

Overall, the Carrier 90MA/MF/MU series stands out as a pinnacle of efficiency, performance, and reliability in the commercial HVAC market. Its advanced technologies and thoughtful design cater to the diverse needs of modern businesses while promoting a sustainable and comfortable indoor environment.