Cisco Systems OL-2056-02 manual Removing Flash Memory SIMMs

Page 22

Chapter 5 Installing Memory in the Router

Replacing Flash Memory SIMMs

Figure 5-16 Flash Memory SIMM Locations on the Cisco 3660 Mainboard

Flash memory SIMMs

	17340
0	1

Removing Flash Memory SIMMs

Perform this procedure to remove a Flash memory SIMM from a mainboard:

Step 1 Attach an ESD-preventive wrist strap and ensure that it makes good contact with your skin. Connect the equipment end of the wrist strap to the metal back plate of the chassis, avoiding contact with the connectors.

Step 2 Locate the Flash memory SIMM sockets on the mainboard. (See Figure 5-14through Figure 5-16.)

Caution Handle SIMMs by the non-connector edges only. SIMMs are ESD-sensitive components and can be damaged by mishandling.

Step 3 To lift the Flash memory SIMM out of its socket, pull the locking spring clips on both sides outward and tilt the SIMM toward the left side of the chassis, free of the clips. (See Figure 5-17.)

Cisco 3600 Series Hardware Installation Guide

5-22	OL-2056-02

Image 22

Contents Installing Memory in the Router Accessing the Mainboard Removing the Cisco 3620 or Cisco 3640 Router CoverPerform the following procedure to remove the chassis cover Removing the Cisco 3631 Router CoverLift cover Slide cover Removing the Cisco 3631 Router CoverRemoving the Cisco 3660 Mainboard Tray Replacing Dram and Sdram Dram SIMMs Used in Cisco 3620 and Cisco 3640 Routers Dram Simm Locations in the Cisco 3620 Router Bank Total Simm Memory 16 MBNot installed 16 MB MB-Dual2 24 MB 32 MB 40 MB 48 MB Bank 0 Simm Total MemoryDram Simm Orientation Dram SimmRemoving Dram Simms Top view Front of chassisInstalling Dram SIMMs Repeat through for each SimmSdram DIMMs Used in the Cisco 3631 and Cisco 3660 Router 64 MB Not installed 32 MB 96 MB 128 MB 160 MB 192 MB 256 MB Bank 0 Simm Bank 1 Simm Total Memory11 Sdram Dimm Locations in the Cisco 3660 Router Sdram Dimm Orientation 12 Sdram Dimm13 Removing and Installing Sdram DIMMs Removing Sdram DimmsInstalling Sdram DIMMs Replacing Flash Memory SIMMs12 MB Bank16 MB 20 MB 12 MB 24 MB 32 MB 64 MB 14 Flash Memory Simm Locations on the Cisco 3620 Mainboard Removing Flash Memory SIMMs 16 Flash Memory Simm Locations on the Cisco 3660 MainboardInstalling Flash Memory SIMMs 17 Removing Flash Memory SIMMsReplacing the ROM Cisco 3620, Cisco 3640, and CiscoLocate the ROM on the mainboard. See -19through Figure 19 ROM Location on the Cisco 3620 Mainboard20 ROM Location on the Cisco 3640 Mainboard 22 Removing the ROM from the Cisco 3660 Mainboard Testing ROM Installation CiscoRouter # upgrade rom-monitor preference readonly upgrade Reboot the router using the new ROM imageSelect the ROM image for next reboot Verify the ROM versionReplacing the Cover on a Cisco 3620 or Cisco 3640 Router 24 Replacing the Cisco 3620 Router CoverReplacing the Cover on a Cisco 3631 Router Insert tabs and slide cover Close cover 26 Replacing the Cisco 3631 Router CoverReplacing the Cisco 3660 Mainboard Tray 27 Replacing the Cisco 3660 Mainboard TrayInstalling a Flash Memory Card 28 Setting the Write-Protect Switch 30 Installing a Flash Memory Card in a Cisco 3660 Router Removing a Flash Memory Card Routerconfig# partition slot1 1 2 Enter global configuration modeRouter# configure terminal Partitioning a Flash Memory CardDisplaying the Contents of a Flash Memory Card Copying a Running Configuration File to a Flash Memory Card Router# copy running-config slot03myconfigCopying a File Between Slots Enter privileged Exec mode as followsRouter# copy slot03TESTFILE flash2TESTFILE2 Booting from a Flash Memory Card Router# copy slot03TESTFILE slot1Erasing the Contents of a Flash Memory Card Preventing Electrostatic Discharge Damage Tools and Equipment NeededCompact Flash Memory Card Installation and Removal Removing the Chassis CoverRemoving the Compact Flash Memory Card Removing the Cover from a CiscoInstalling the Compact Flash Memory Card Instructions on formatting the Compact Flash memory cardReinstalling the Cover Replacing the Cover on a CiscoROM monitor to recognize and boot the Flash Formatting Procedures for Compact Flash Memory CardsSafety Information document that accompanied this device Determining the File System on a Compact Flash Memory CardClass B Flash file system CommandFormatting Compact Flash Memory as a DOS File System Router# format flashRouter# copy flashmy-config2 running-config File and Directory ProceduresProcedures for Use with DOS File System File OperationsDisplay Geometry and Format Information Display the Contents of a Compact Flash CardDelete Files from Compact Flash Memory Display the Contents of a File Rename a File in FlashCreate a New Directory Directory OperationsRemove a Directory Procedures for Use with Class B Flash File System Enter a Directory and Determine Which Directory You AreDisplay the Contents of a Compact Flash Memory Card Router# squeeze flash Router# more flashc3725-i-mzOL-2056-02