Cisco Systems OL-2056-02 File and Directory Procedures, Procedures for Use with DOS File System

Page 51

Chapter 5 Installing Memory in the Router

Installing and Formatting Compact Flash Memory Cards in Cisco 3631 Routers

eeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeee eeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeee eeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeee eeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeee eeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeee eeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeee

...erased

Erase of flash: complete

File and Directory Procedures

The following sections describe file and directory procedures for internal Compact Flash memory cards. File and directory procedures vary according to the formatted file system—Class B or Class C.

Procedures for Use with DOS File System

The following file and directory procedures are useful for Compact Flash memory cards formatted with a Class C Flash file system.

File Operations

Copy Files

To copy the files to another location, use the copy flash: source-filename{flash: tftp: lex: null:

nvram: pram: rcp: system: tftp: xmodem: ymodem: running-config startup-config}destination-filenamecommand.

The following example shows output for copying a configuration file to the startup configuration in an internal Compact Flash memory card (flash:):

Router# copy flash:my-config1 startup-config Destination filename [startup-config]?

[OK]

517 bytes copied in 4.188 secs (129 bytes/sec)

The following example shows output for copying a configuration file to the running configuration in an internal Compact Flash memory card (flash:):

Router# copy flash:my-config2 running-config

Destination filename [running-config]? 709 bytes copied in 0.72 secs

Cisco 3600 Series Hardware Installation Guide

	OL-2056-02	5-51

Image 51

Contents Installing Memory in the Router Removing the Cisco 3620 or Cisco 3640 Router Cover Accessing the MainboardRemoving the Cisco 3631 Router Cover Perform the following procedure to remove the chassis coverRemoving the Cisco 3631 Router Cover Lift cover Slide coverRemoving the Cisco 3660 Mainboard Tray Replacing Dram and Sdram Dram SIMMs Used in Cisco 3620 and Cisco 3640 Routers Dram Simm Locations in the Cisco 3620 Router 16 MB Bank Total Simm MemoryBank 0 Simm Total Memory Not installed 16 MB MB-Dual2 24 MB 32 MB 40 MB 48 MBDram Simm Dram Simm OrientationTop view Front of chassis Removing Dram SimmsRepeat through for each Simm Installing Dram SIMMsSdram DIMMs Used in the Cisco 3631 and Cisco 3660 Router Bank 0 Simm Bank 1 Simm Total Memory 64 MB Not installed 32 MB 96 MB 128 MB 160 MB 192 MB 256 MB11 Sdram Dimm Locations in the Cisco 3660 Router 12 Sdram Dimm Sdram Dimm OrientationRemoving Sdram Dimms 13 Removing and Installing Sdram DIMMsReplacing Flash Memory SIMMs Installing Sdram DIMMsBank 12 MB16 MB 20 MB 12 MB 24 MB 32 MB 64 MB 14 Flash Memory Simm Locations on the Cisco 3620 Mainboard 16 Flash Memory Simm Locations on the Cisco 3660 Mainboard Removing Flash Memory SIMMs17 Removing Flash Memory SIMMs Installing Flash Memory SIMMsCisco 3620, Cisco 3640, and Cisco Replacing the ROM19 ROM Location on the Cisco 3620 Mainboard Locate the ROM on the mainboard. See -19through Figure20 ROM Location on the Cisco 3640 Mainboard 22 Removing the ROM from the Cisco 3660 Mainboard Cisco Testing ROM InstallationVerify the ROM version Reboot the router using the new ROM imageSelect the ROM image for next reboot Router # upgrade rom-monitor preference readonly upgrade24 Replacing the Cisco 3620 Router Cover Replacing the Cover on a Cisco 3620 or Cisco 3640 RouterReplacing the Cover on a Cisco 3631 Router 26 Replacing the Cisco 3631 Router Cover Insert tabs and slide cover Close cover27 Replacing the Cisco 3660 Mainboard Tray Replacing the Cisco 3660 Mainboard TrayInstalling a Flash Memory Card 28 Setting the Write-Protect Switch 30 Installing a Flash Memory Card in a Cisco 3660 Router Removing a Flash Memory Card Partitioning a Flash Memory Card Enter global configuration modeRouter# configure terminal Routerconfig# partition slot1 1 2Displaying the Contents of a Flash Memory Card Router# copy running-config slot03myconfig Copying a Running Configuration File to a Flash Memory CardEnter privileged Exec mode as follows Copying a File Between SlotsRouter# copy slot03TESTFILE flash2TESTFILE2 Router# copy slot03TESTFILE slot1 Booting from a Flash Memory CardErasing the Contents of a Flash Memory Card Tools and Equipment Needed Preventing Electrostatic Discharge DamageRemoving the Chassis Cover Compact Flash Memory Card Installation and RemovalRemoving the Cover from a Cisco Removing the Compact Flash Memory CardInstructions on formatting the Compact Flash memory card Installing the Compact Flash Memory CardReplacing the Cover on a Cisco Reinstalling the CoverDetermining the File System on a Compact Flash Memory Card Formatting Procedures for Compact Flash Memory CardsSafety Information document that accompanied this device ROM monitor to recognize and boot the FlashRouter# format flash CommandFormatting Compact Flash Memory as a DOS File System Class B Flash file systemFile Operations File and Directory ProceduresProcedures for Use with DOS File System Router# copy flashmy-config2 running-configDisplay the Contents of a Compact Flash Card Display Geometry and Format InformationDelete Files from Compact Flash Memory Rename a File in Flash Display the Contents of a FileDirectory Operations Create a New DirectoryRemove a Directory Enter a Directory and Determine Which Directory You Are Procedures for Use with Class B Flash File SystemDisplay the Contents of a Compact Flash Memory Card Router# more flashc3725-i-mz Router# squeeze flashOL-2056-02