Cisco Systems OL-2056-02 manual Compact Flash Memory Card Installation and Removal

Page 45

Chapter 5 Installing Memory in the Router

Installing and Formatting Compact Flash Memory Cards in Cisco 3631 Routers

Compact Flash Memory Card Installation and Removal

Perform the procedure below for installing or removing a Compact Flash memory card mounted internally on the router CPU/mainboard. To access the internal Compact Flash memory card, you need to remove the chassis cover.

Removing the Chassis Cover

This section describes how to remove the chassis cover to access the Compact Flash memory card. You need a number 2 Phillips or flat-blade screwdriver to perform this procedure.

Observe the following precaution if your router uses AC or DC power:

Warning Do not touch the power supply when the power cord is connected. For systems with a power switch, line voltages are present within the power supply even when the power switch is OFF and the power cord is connected. For systems without a power switch, line voltages are present within the power supply when the power cord is connected. To see translations of the various warnings that appear in this publication, refer to the Regulatory Compliance and Safety Information document that accompanied this device.

Observe the following precaution if your router uses DC power:

Warning Before performing any of the following procedures, ensure that power is removed from the DC circuit. To ensure that all power is OFF, locate the circuit breaker on the panel board that services the DC circuit, switch the circuit breaker to the OFF position, and tape the switch handle of the circuit breaker in the OFF position. To see translations of the various warnings that appear in this publication, refer to the Regulatory Compliance and Safety Information document that accompanied this device.

Perform the following procedure to remove the chassis cover:

Step 1 Power OFF the router. However, to channel ESD voltages to ground, do not unplug the power cable.

Warning Before opening the chassis, disconnect the telephone-network cables to avoid contact with telephone-network voltages. To see translations of the various warnings that appear in this publication, refer to the Regulatory Compliance and Safety Information document that accompanied this device.

Step 2 Disconnect all network interface cables from the rear panel.

Step 3 Place the router on a flat surface. Remove the five screws located on top of the cover. Set the screws aside in a safe place.

Step 4 Rotate the cover up to a 45-degree angle. (See Figure 33.)

•Slide the cover to the side (away from the side with the fans) until the tabs are free from the slots. (See Figure 33.)

Cisco 3600 Series Hardware Installation Guide

 

OL-2056-02

5-45

 

 

 

Page 44 Page 46
Image 45
Page 44 Page 46
Contents Installing Memory in the Router Removing the Cisco 3620 or Cisco 3640 Router Cover Accessing the MainboardRemoving the Cisco 3631 Router Cover Perform the following procedure to remove the chassis coverRemoving the Cisco 3631 Router Cover Lift cover Slide coverRemoving the Cisco 3660 Mainboard Tray Replacing Dram and Sdram Dram SIMMs Used in Cisco 3620 and Cisco 3640 Routers Dram Simm Locations in the Cisco 3620 Router 16 MB Bank Total Simm MemoryBank 0 Simm Total Memory Not installed 16 MB MB-Dual2 24 MB 32 MB 40 MB 48 MBDram Simm Dram Simm OrientationTop view Front of chassis Removing Dram SimmsRepeat through for each Simm Installing Dram SIMMsSdram DIMMs Used in the Cisco 3631 and Cisco 3660 Router Bank 0 Simm Bank 1 Simm Total Memory 64 MB Not installed 32 MB 96 MB 128 MB 160 MB 192 MB 256 MB11 Sdram Dimm Locations in the Cisco 3660 Router 12 Sdram Dimm Sdram Dimm OrientationRemoving Sdram Dimms 13 Removing and Installing Sdram DIMMsReplacing Flash Memory SIMMs Installing Sdram DIMMsBank 12 MB16 MB 20 MB 12 MB 24 MB 32 MB 64 MB 14 Flash Memory Simm Locations on the Cisco 3620 Mainboard 16 Flash Memory Simm Locations on the Cisco 3660 Mainboard Removing Flash Memory SIMMs17 Removing Flash Memory SIMMs Installing Flash Memory SIMMsCisco 3620, Cisco 3640, and Cisco Replacing the ROM19 ROM Location on the Cisco 3620 Mainboard Locate the ROM on the mainboard. See -19through Figure20 ROM Location on the Cisco 3640 Mainboard 22 Removing the ROM from the Cisco 3660 Mainboard Cisco Testing ROM InstallationSelect the ROM image for next reboot Reboot the router using the new ROM imageRouter # upgrade rom-monitor preference readonly upgrade Verify the ROM version24 Replacing the Cisco 3620 Router Cover Replacing the Cover on a Cisco 3620 or Cisco 3640 RouterReplacing the Cover on a Cisco 3631 Router 26 Replacing the Cisco 3631 Router Cover Insert tabs and slide cover Close cover27 Replacing the Cisco 3660 Mainboard Tray Replacing the Cisco 3660 Mainboard TrayInstalling a Flash Memory Card 28 Setting the Write-Protect Switch 30 Installing a Flash Memory Card in a Cisco 3660 Router Removing a Flash Memory Card Router# configure terminal Enter global configuration modeRouterconfig# partition slot1 1 2 Partitioning a Flash Memory CardDisplaying the Contents of a Flash Memory Card Router# copy running-config slot03myconfig Copying a Running Configuration File to a Flash Memory CardEnter privileged Exec mode as follows Copying a File Between SlotsRouter# copy slot03TESTFILE flash2TESTFILE2 Router# copy slot03TESTFILE slot1 Booting from a Flash Memory CardErasing the Contents of a Flash Memory Card Tools and Equipment Needed Preventing Electrostatic Discharge DamageRemoving the Chassis Cover Compact Flash Memory Card Installation and RemovalRemoving the Cover from a Cisco Removing the Compact Flash Memory CardInstructions on formatting the Compact Flash memory card Installing the Compact Flash Memory CardReplacing the Cover on a Cisco Reinstalling the CoverSafety Information document that accompanied this device Formatting Procedures for Compact Flash Memory CardsROM monitor to recognize and boot the Flash Determining the File System on a Compact Flash Memory CardFormatting Compact Flash Memory as a DOS File System CommandClass B Flash file system Router# format flashProcedures for Use with DOS File System File and Directory ProceduresRouter# copy flashmy-config2 running-config File OperationsDisplay the Contents of a Compact Flash Card Display Geometry and Format InformationDelete Files from Compact Flash Memory Rename a File in Flash Display the Contents of a FileDirectory Operations Create a New DirectoryRemove a Directory Enter a Directory and Determine Which Directory You Are Procedures for Use with Class B Flash File SystemDisplay the Contents of a Compact Flash Memory Card Router# more flashc3725-i-mz Router# squeeze flashOL-2056-02
Top Page Image Contents