Storage, Disposal, Intake AIR Cooling Vent, Oil

NS3526

10. Maintenance

INTAKE AIR COOLING VENT

WARNING

•Never touch the cylinder, muffler, or spark plugs with your bare hands immediately after stopping the engine. The engine can become very hot when in operation, and doing so could result in severe burns.

•When checking the machine to make sure that it is okay before using it, check the area around the muffler and remove any wood chips or leaves which have attached themselves to the brushcutter. Failing to do so could cause the muf- fler to become overheated and that in turn could cause the engine to catch on fire. Always make sure that the muffler is clean and free of wood chips, leaves, and other waste before use.

•Check the intake air cooling vent and the area around the cylinder cooling fins after every 25 hours of use for blockage. Note that it is neces- sary to remove the upper cover and the lower cover in order to be able to view the upper part of the cylinder.

IMPORTANT

	(1) Intake air	G
		B
	cooling vent

OIL

•After first 20 hours of use, replace the gear oil. After that, replace it after every 100 hours of use (SAE40CC, 100cc).

(1) bolt

(1) (2) window

(3) drain bolt

(2)

(3)

GREASE

•Open the upper lid of the grease cup and check the grease amount. Fill it up if it is decreasing. (#3)

• If waste gets stuck and causes blockage around the	(1)	(1) grease cup
intake air cooling vent or between the cylinder fins, it	(1)
intake air cooling vent or between the cylinder fins, it
may cause the engine to overheat, and that in turn
may cause mechanical failure on the part of the
brushcutter.

11. Storage

WARNING

•When draining fuel, please be careful not to spill it. If fuel is spilt, wipe off thoroughly. In addition, please be sure to close the storage container cap tightly.

IMPORTANT

•If fuel is left in the engine for protracted periods, the inside of the carburetor may become clogged and cause engine malfunction (faulty starting and insuffi- cient output).

•During storage, slightly loosen the cap of the chemi- cal fluid tank. If screwed too tightly, the gasket may become distorted.

On completion of all work procedures, when not plan- ning to use again for a protracted period please carry out the following pre-storage care, to prevent trouble caused by time-lapse changes.

1.Clean the chemical fluid tank and nozzle (see page 10).

2.Remove dirt from the sprayer, inspect it for any dam- age or looseness, and, if any abnormality is found, correct it thoroughly in preparation for the next time you use the unit.

3.Drain the fuel tank.

4.Start the engine, and leave it in idling condition until all the fuel inside the carburetor is spent and the en- gine comes to a natural stop.

5.Remove the spark plug and put a few drops (1 to 2 cc) of 2-cycle oil inside the engine. After pulling the starter rope 2 or 3 times, return the spark plugs to their original position and stop in compressed posi- tion.

6.After oiling the throttle lever and other metal parts with anti-corrosive oil, cover the sprayer and store indoors in a low-humidity location.

12. Disposal

When disposing your machine, fuel or oil for the machine, be sure to allow your local regulations.

GB-13

NS3526 specifications

The Zenoah NS3526 is a high-performance engine that stands out in the realm of small engines, particularly for applications requiring power and reliability. Known for its robust design and efficiency, the NS3526 is widely used in various fields, from professional landscaping to consumer gardening tools.

One of the defining features of the NS3526 is its displacement of 35.2 cc, which strikes an ideal balance between power output and size. This engine is specifically engineered for high torque, allowing it to manage tough tasks without compromising on performance. With its lightweight construction, the NS3526 enhances maneuverability and reduces user fatigue during extended periods of operation.

The engine integrates advanced technologies to improve its efficiency and user-friendliness. One notable feature is the electronically controlled ignition system, which ensures reliable starting and consistent performance under varying load conditions. This technology reduces maintenance needs and enhances fuel economy, making the NS3526 a cost-effective choice for users.

Its engine design incorporates a two-stroke cycle, which effectively delivers high power while minimizing weight. This is particularly beneficial for handheld equipment and other applications where portability is a primary concern. The NS3526's ability to deliver impressive power in a compact form makes it ideal for use in chainsaws, trimmers, and blowers.

Another characteristic of the Zenoah NS3526 is its high-quality materials. Built to withstand harsh environments, the engine features durable components that enhance longevity and operational stability. Its anti-vibration system minimizes user fatigue, facilitating comfortable operation even during prolonged use.

The NS3526 is not only about raw power but also about adaptability. It is compatible with a range of attachments, which allows users to customize their equipment according to their specific needs. Whether cutting, trimming, or blowing leaves, the versatility of the Zenoah NS3526 makes it a valuable asset for professionals and hobbyists alike.

In conclusion, the Zenoah NS3526 sets a high standard in the small engine market with its combination of power, efficiency, and durability. Its innovative technologies and thoughtful design make it a trusted choice for those who demand reliability in their outdoor equipment. Whether you are a professional landscaper or a homeowner tending to your yard, the NS3526 delivers the performance you can rely on.