Genesis Advanced Technologies GTS10S manuel dutilisation Miter Cross Cutting, Bevel Cross Cutting

Page 14
FIG. 16

English

Miter Cross Cutting:

Warning: Make sure the blade guard assembly is properly installed to avoid serious personal injury

1.Remove the rip fence from the table surface

2.Position Miter Gauge to the desired degree. (0°-60°). (Refer to Miter Gauge Adjustment).

3.Make sure all loose pieces have been removed from the table surface and work piece is not in contact with blade

4.Turn ON/OFF switch to the ON position

5.Position the work piece flat on the table with edge flush against miter gauge fence. Wait until blade reaches full speed before feeding the work piece into the blade

6.Use two hands to slowly feed the work piece and miter gauge toward the blade. Use the hand furthest from the blade to keep the work piece flush

against miter gauge fence and use your other hand to push the miter gauge and work piece toward the blade. Stand slightly to the side of the blade to reduce the risk of injury should kickback occur.

7. Continue feeding the work piece into the blade until the cut has been completed.

8.Once the cut has been completed, pull the work piece back toward you

9.Turn the switch off

10.After blade has stopped completely, remove the cut off piece.

Bevel Cross Cutting:

Warning: Make sure the blade guard assembly is properly installed to avoid serious personal injury

1.Remove the rip fence from the table surface

2.Adjust bevel angle to the desired degree. (0°-45°)

3.Set the blade to the correct depth. Refer to Blade Height Adjustment

4.Position Miter Gauge to 0°. (Refer to Miter Gauge Adjustment). Use the miter gauge in the groove to the RIGHT of the blade. It can not be used in the groove to the LEFT because the blade guard will interfere with the cut .

5.Make sure all loose pieces have been removed from the table surface and work piece is not in contact with blade

6.Turn ON/OFF switch to the ON position

7.Position the work piece flat on the table with edge flush against miter gauge fence. Wait until blade reaches full speed before feeding the work piece into the blade

8.Use two hands to slowly feed the work piece and miter gauge toward the blade. Use the hand furthest from the blade to keep the work piece flush against miter gauge fence and use your other hand to push the miter gauge and work piece toward the blade. Stand slightly to the side of blade to

 

reduce the risk of injury should kickback occur.

FIG. 17

9.

Continue feeding the work piece into the blade until the cut has been completed.

 

10.

Once the cut has been completed, pull the work piece back toward you

 

11.

Turn the switch off

 

12.

After blade has stopped completely, remove the cut off piece

 

Compound Miter Cross Cutting

Warning: Make sure the blade guard assembly is properly installed to avoid serious personal injury

1.Remove the rip fence from the table surface

2.Adjust bevel angle to the desired degree. (0°-45°) (refer to Bevel Adjustment)

3.Set the blade to the correct depth

4.Position the Miter Gauge to the desired degree. (0°-60°) (Refer to Miter Gauge Adjustment). Use the miter gauge in the groove to the RIGHT of the blade. It can not be used in the groove to the LEFT because the blade guard will interfere

5.Make sure all loose pieces have been removed from the table surface and work piece is not in contact with blade

6.Turn ON/OFF switch to the ON position

7.Position the work piece flat on the table with edge flush against miter gauge fence. Wait until blade reaches full speed before feeding the work piece into the blade

8.Use two hands to slowly feed the work piece and miter gauge toward the blade. Use the hand furthest from the blade to keep the work piece flush against miter gauge fence and use your other hand to push the miter gauge and work piece toward the blade. Stand slightly to the side of blade to reduce the risk of injury should kickback occur.

9.Continue feeding the work piece into the blade until the cut has been completed.

10.Once cut has been completed, pull the work piece back toward you

11.Turn the switch off

12.After blade has stopped completely, remove the cut off piece

10" Table Saw

 

Operator’s Manual

GTS10S

Image 14
Contents Table Saw Operator’s Manual General Safety Rules EnglishPersonal Safety Work Area SafetyElectrical Safety Tool USE and CareService Specific Safety Rules for Table SAW Extension CordsNever reach behind blade when the saw blade is rotating Glossary of WOOD-WOKING Terms Unpacking and Contents Your 10 Table SAWMounting the Table SAW on Stand Assembly and AdjustmentWork Stand Assembly Mounting the Table Without StandMiter Gauge Installation Blade Guard Assembly InstallationBlade Guard Adjustment Miter Gauge Adjustment45 Positive Stops Adjustment RIP Fence AdjustmentBlade Height Adjustment Adjust 90 Positive StopOperation Cross Cutting ApplicationsCutting Tips Rip CuttingCompound Miter Cross Cutting Miter Cross CuttingBevel Cross Cutting To Remove or Change the Blade To remove the blade MaintenanceNon-Through Cutting TOLL-FREE Help Line Trouble ShootingTWO-YEAR Warranty