Sioux Tools manual Model 5978A

Model 5978A

118" (3 mm) Pencil Air Die Grinder

Form # ZCE568A Date 6-03lA

Operator Instructions

Includes - Foreseen Use, Work Stations, Putting Into Service,

Operating, Dismantling, Assembly and Safety Rules.

Manufacturer/Supplier

Sioux Tools, Inc.

250Snap-on Drive P.O. Box 1596 Murphy, NC 28906 U.S.A.

Tel No. 828-835-9765 Fax No. 828-835-9685

Important

Read these instructions carefully before installing, operating, servicingor repairing this tool. Keepthese instructions in a safe accessible olace.

Product TypeRPMce

54000

118" (3 mm) Pencil~ m . Cycles Per

Air Die Grinder

Model NotNos Serial No.

Product Net Weight		Recommended Use Of				Recommended Hose Bore		Recommended Max.
0.44	Ibs	Balancer Or Support				Size - Minimum		Hose Length
0.20	Kg		NO			5/16 ins	8 mm	30 Ft	10 M
	Air Pressure					Noise Level: Sound Pressure Level 72.0 dB(A)
							Sound Power Level		84.0 dB(A)
Recommended Working		6.2	bar	90	PSI	Test Method: Tested in accordance with Pneurop
Maximum		6.2	bar	90	PSI

test code PN8NTC1 andISO Standard 3744

e -a	Personal Safety Equipment		1	a
	a s s e s	Y E
Use - Safety Gloves		YES
Use - Safety Boots				@

		- '
	> *
Always Read Instructions	vibration Level	2.0 Meters / Sec2
Before Using PowerTools	Test Method: Tested in accordance with I S 0
H^s wear
Goggles	standards 8662 Parts 1& 13

Wear HearingProtection

Use - BreathingMasks	YES	A ~	~ b ~ Expsure~ ~ g e	d
Use - Ear Protectors	YES
Safety rules when using 5978A				chance of coming into contact with live electricity.
Pencil Die Grinder			-Always when using the tool, adopt a firm footing and/or
				position and grip the tool sufficiently only to overcome
- Use accessories rated at least 54.000 RPM.				any reactionforces that may result from the tool doing
- Prolonged exposure to vibration may cause injury.				work. Do not overgrip.
-Read all instructions before using this tool. All				-Use only correct spare parts for maintenance and
operators must be fully trained in its use and aware of				repair. Do not improvise or make temporary repairs.
these safety rules.				Major servicing and repairs should only be carried out
- Do not exceed the maximum working air pressure.				by persons trained to do so.
- Use personal protection equipment as recommended.				- Do not lock, tape, wire, etc. the 'OnIOtfvalve in 'On'
-Some dust created by power sanding, sawing, grinding,				position.The triggerllever, etc. must always be free to
drilling, and other construction activities contains				return to the 'Off'position when released.
chemicals knownto cause cancer, birthdefects and other				-Always shut off the air supply to the tool and press the
reproductiveharm.				On/Off1valve to exhaust the air from the feed hose
-Use only compressed air at the			recommended	before fitting,	removing or adjusting the working
conditions.				attachment fitted to the tool.
- If the tool appears to malfunction, remove from use				- Before using the tool, make sure that a shut off device
immediately and arrange for service
and reoair. If it is not oractical to 7					Take Air From Top
remove tool from service, then shut			All PipeAnd Fittings
off the air supply to the tool and write
			Should Be 112"Or Larger
or have written a warning note and			Compressor
attach it to the tool.
			with Sufficient Capacity
- If tool is to be used with a balancer or			To MaintainRecommended
other suspension device, ensure that			Working PressureAt
the tool is firmly attached to the			EachTool Outlet
suspension/support device.
-When operatingthe tool, always keep					Drain Daily
the body and particularly the hands
					L
away from the working attachment
fixed to the tool.
-The tool is not electrically insulated.			Recommended Air Supply System		Figure 1
Never use the tool if there is any

Page No 1